I need the answer as soon as possible R1ci12V213R2V1V3C2V1RC-CircuitV2For the circuit shown above, answer the following questions:a) Write the state equation governing the circuit shown aboveb) Assuming that the system output is V2, write the output equation and compute thetransfer functionc) Assuming that the system output is 12, write the output equation and compute thetransfer functiond) Determine the state transition matrix of the systeme) Assuming zero input (V1=0) and the voltage on C1 Vei=1 volt and voltage on C2 Vc2=-.1 volt, compute the output (V2(t)) at all time.f) Write the form-1 state space representation of the circuit (the phase variable canonicalform)g) Write the form-2 state space representation of the circuit (the input feedforwardcanonical form)

Answered: Image /qna-images/answer/a07542d1-60ac-4a4e-b8d3-ea6444865366.jpg

Answered: 12 V2 13 R2 V1 V3 c2 V1- RC-Circuit V2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Each item below describes key characteristics of a particular system (that is, a plant transfer function). For each system, describe the effect of proportional control on the stability of the closed-loop system. Specifically, 1) what can you say for small gains, and 2) what for large gains? (E.g., stable, unstable, inconclusive.) Provide a short explanation of your answers, with sketches as necessary.
Figure Q2 shows the block diagram of a flight control system.a) Derive the system transfer function.b) Find out the system gain, natural frequency and damping ratio for this systembased on the standard form of second order systems.c) If K1 = 2 and K2 = 10, use the standard response sheet to find out the systemsteady-state value, overshoot and 63% rise time, with a unit step input.
Electrical Engineering - Data Signal Processing ( EENG420) Please solve the question quickly and with the step
Analyze the circuit below and provide what are being ask in the problem e.f. Determine the DC voltagesDetermine the DC currents??1,, ??2,, ??1, , ??, and2 , ??1 and ??2 g. Solve for the input and output impedances??1 ??2 ??1 ??2 ??2 h. Solve for the voltage gain and current gain
Draw the Nyquist plot for the system in the figure below. Using the Nyquist stability criterion, determine the range of K for which the system is stable. Consider both positive and negative values of K.( Need only handwritten solution please otherwise downvote)
Please find the following:(a) The error constants Kp, Kv and Ka and also the system type.(b) The range of K so that the steady-state error (i.e., e(t) = r(t) - c(t) as t -> ∞)under a unit ramp input is less than 0.01.(c) The range of K that keeps the system stable. (d) The value of K that makes the system oscillate and also the frequency ofoscillation. (e) Suppose that we replace the constant gain controller K with the moresophisticated PI controller, i.e., Gc(s) = K + (KI/s), find the range of thecontroller gains (K, KI) so the system is stable.
A university wants to establish a control system model that represents the student population as an output, with the desired student population as an input. The administration determines the rate of admissions by comparing the current and desired student populations. The admissions office then uses this rate to admit students. Draw a functional block diagram showing the administration and the admissions office as blocks of the system. Also show the following signals: the desired student population, the actual student population, the desired student rate as determined by the administration, the actual student rate as generated by the admissions office, the dropout rate, and the net rate of influx
please write an Equation for VSG, VSD and Vout . Please label the circuit to be clear.
Evaluate and sketch the block diagram representation of the Direct Form I and IIfor the following IIR system function:
a) Derive the governing differential equation for vc(t)
A gas stove system has to be in automation form to enhance easy regulation and control. Make a drawing of a functional block diagram which shows the output and input transducers, the plant, controller response & reference.
The self-bias configuration drawn below has an operating point defined by VGSQ = -2.6 V and IDQ = 2.6 mA, with IDSS = 12 mA and VP = -8 V,with VDD=18 V, RD=3.5KὩ, Rs=1.2KὩ and RG=1.2MὩ an applied signal V i . The value of gos is given as 30 mS.a. Determine gm.b. Find rd.c. Find Zi.d. Calculate Zo with and without the effects of rd. Compare the results. e. Calculate Av with and without the effects of rd. Compare the results.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS