Write the solution on a piece of paper 12. The uniform bar and the homogeneous cylinder each have a mass of 40 kg. Assumingequilibrium, calculate the normal and friction forces at A, B, and C. (b) what is the smallestvalue of us necessary for equilibrium?3m2m BR 0.6666 m

Answered: Image /qna-images/answer/921bb021-87f7-4fe4-a5c3-01b18d326477.jpg

Answered: 12. The uniform bar and the homogeneous…

12. The uniform bar and the homogeneous cylinder eac equilibrium, calculate the normal and friction forces at value of us necessary for equilibrium? 3m R 0.6666m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 8. A laboratory provides the following analysis obtained from a 50-ml sample of raw water: Ca - 60…

Q: You are asked to design a square footing that will be placed 5 feet below the ground surface in…

A: iven

Q: A 500-ft curve, 9₁ = -2.00%, 9₂ = +3.00 %, VPI station = 98 + 10, VPI elevation = 5388.26 ft,…

A: g1 = -2.00%g2= +3.00%L = 500ftPvi elevation = 5388.26ftPvi station = 98+10To find:Elevations

Q: Consider a concrete (n=0.013) wide rectangular channel that discharges 2.0 m/sec per unit bxh width…

A: Wide rectangular channel Discharge per unit width (q) = 2 m3/s/m Bed slope of the channel (So) =…

Q: A k 3m D B 6KN-MIE 1 1.5m 1.5m 5KN Point D is located just to the left of the roller support at B.…

A: An overhanging beam is given, with a hinge at the left end and supported on a roller at 3m from the…

Q: The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes…

A: Given:Required:Force diagramMagnitude of concentrated force FCDTension forces in terms of TNote: As…

Q: A U-tube with both ends open to the atmosphere contains glycerol in the lower portion. In one leg,…

Q: 4. Suppose a person can reduce the pressure in his lungs to -275 mmHg gauge pressure. How high can…

A: change in pressure=p=275mmm Hgheight of water sucked=?

Q: A Warren bridge truss is loaded as shown in the figure. Determine the force in members EG, FG, and…

A: Determine the force in members EG, FG and FH using method of section.

Q: Discuss the relationship between bending moment, shear force and deflection, please provide all the…

A: The relationship between bending moment, shear force, and deflection is fundamental to the study of…

Q: Compute the coordinates of the centroid (x, y) of the area shown. Also compute the area moment of…

A: VariableValuea12 mmb112 mmc11 mmd45 mmh107 mmw20 mmThe x coordinate of the centroid is =? in mm.The…

Q: solve the fixed-end moment of the beam shown below using CONJUGATE METHOD. show the step by step…

A: Given:Required:Fixed end moment using conjugate beam method

Q: Design the middle concrete beam B1 shown below, the service live load of 2 kN/m² and the service…

Q: e shown in the figure below is hinged @ point B and rests agai e, assuming fresh water. Hinge now…

Q: Give three examples of different types of tensile structures and their application

A: A tensile structure is a type of construction characterized by elements such as cables, membranes,…

Q: P12.3. Draw the influence lines for the reactions at supports A and C, the shear and moment at…

Q: The truss below is to be analyzed using the Method of Sections. 2 kN A 4- 5m 4 kN H B 5m 4 KN C G…

A: Take moment about E

Q: All angles in this bridge are either 90 degrees or 45 degrees Suppose that the applied force F =…

A: Given:F = 250.0 NRequired:Force in member between joints 1and 2

Q: a) Dimensioning of concrete beam i borderline conditionA free-standing beam in concrete with 4Φ20…

A: The objective of the question is to estimate the load that a concrete beam can handle according to…

Q: ing characteristics and carries condition, determine the tota

A: Number of Lanes = 4Shutted down lanes = 2 Volume of traffic = 4250 veh/hrTime to clear obstruction =…

Q: B f 900 lb 2 ft 200 lb/ft 6 ft The properties of the timber cantilever beam ABC are I = 60 in.4 and…

Q: Given the simply supported beam below, and using the method of sections: m 1.5m 1.5m * 1.5m * KN…

Q: incorrect please recheck i did the same method and got it incorrect , the book answer is 78.48kn

A: A vertical Sluice gate width = 2m depth = 2mUpstream side water…

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: The first thing you need to do in a tape and offset survey is: Question Select one: A. Create a…

A: We need to choose correct option based on given statement

Q: What is the process to uncloggrd sand drain?

A: Sand Drain is based on principles of rapid and centrally dewatering system.Sand Drain is a process…

Q: . A pumping well with a radius of 0.5 m is located midway between a river and an impermeable…

A: This is a question related to groundwater hydraulics. The steady draw down at a point in a confined…

Q: how to calculate self weigth of coloumn of wood

A: The objective of the question is to calculate the self-weight of a wooden column. The self-weight of…

Q: X- 12" -1" 6" 1" 9" 2" -X

A: Locate the X-X and Y-Y centroidal axes for the area shown above the question.Solve useing chart -

Q: ater with a total head of H= 12 m flows freely from a reservoir into a concrete trapezoid annel with…

A: Water with a total head of different longitudinal slopes of,The channel was designed using the most…

Q: 2. In Figure 2, draw the shear and moment diagrams for the beam. -3 m- 6 m 12 kN/m B

Q: Det the member end moments and reactions using slope Def. Method (No Side sway) 50KM/m A 7m B.) 10…

A: Dear student as per our company guidelines i am solving problem A only

Q: Given the simply supported beam below, and using the method of sections: 6KN m * 1.5m The internal…

Q: With clear sketch Prove the parallel axis theorem equation is 1 = Ï + Ad²

A: Parellel axis theoremThe parallel axis theorem relates the moment of inertia of a rigid body about…

Q: A single-story home with infiltration rate of 0.5 ach has 200 m2 of floor space and a total volume…

Q: For questions 1 to 5, consider a bent rod fixed at the wall at A and is acted upon by a 20- N force…

A: 20 N force is parallel to the z-axis50N force is parallel to the y-axisbend rod fixed at the wall…

Q: Problem 5: Dimensional Analysis Use the Buckingham Pi Theorem (Song, 2018, pages 219-221) to derive…

A: Gravitational accelerationPipe diameterPipe lengthAverage velocityTo find: Equation for friction…

Q: 2. The average wastewater flow from a community of 20,000 is 125 gpcd. The 5 day, 20 deg C BOD is…

A: Population = 20000To Find:1) Settling tank surface area2) Settling tank diameter3) BOD removal in…

Q: Cutting a structure is the most important step when applying Method of Sections. Which of the…

A: The rules pertaining to method of sections are given out of which correct options has to be choosen.

Q: 4. A square foundation will be constructed at ground surface. The subsoil profile is shown in the…

Q: Explain the major steps involved in an engineering survey. b) Explain the purpose of the…

A: Find: Major steps involved in an engineering survey b) (i) National Geodetic Datum (ii)…

Q: he center of a rectangular area at the ground surface has Cartesian coordinates (0, 0), and one…

A: z = 15 m & uniform pressure = 135 kPa

Q: 4- A moderately curved channel with a slightly rounded non-cohesive bed material with a diameter of…

A: The Discharge is,

Q: What is the equation for bending moment between C and B, the midpoint and righ side of the beam (6…

A: Determine the moment equation for the span CB (6ft<x<12ft).

Q: y using a BAF 20 instrument, 180 trees were takkued at 25 points. The sum of the volune (cu ft) /…

A: 180 trees were tallied.BAF (Basal Area Factor) = 20.The sum of volume (cu ft) / basal-area ratios…

Q: 6-14 to 6-17 Refer to Figs. P6-14 to P6-17. Determine the components of the resul- tant of the two…

Q: below shows the sieve size and corresponding weight retained for 3 different stockpiles. Calculate…

A: The objective of the question is to calculate the percent passing for all the 3 aggregate…

Q: 2 ft a. b. 4 ft 36 k/ft 1.5 ft 2 ft Reaction at the hinge support in kips Reaction at the roller…

A: a. Reaction at hinge support in kips =?b. Reaction at roller support in kips =?

Q: 3. A settling tank has an overflow rate of 100,000 gal/ft² d. Water carrying sediment of various…

A: Overflow rate = 100,000 gal/ft2settling velocitymass friction…

Q: If the shear stress at point A is 60 kPa, compute the short-term and long-term factors of safety at…

Concept explainers

Pressure and Stress

Question

Write the solution on a piece of paper

12. The uniform bar and the homogeneous cylinder each have a mass of 40 kg. Assuming
equilibrium, calculate the normal and friction forces at A, B, and C. (b) what is the smallest
value of us necessary for equilibrium?
3m
2m B
R 0.6666 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the normal and friction forces at A, B, C and smallest value of us

VIEW

Step 2: Determine the normal and friction forces at A, B, C and smallest value of us

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2.15 The tire of an airplane is inflated at sea level to 410 KN/m2 Assuming the tire does not expand, what is the pressure within the tire at elevation 9000 m? Assume standard atmosphere. Express the answer in KN/m2 and KN/m2, abs.
Determine the moment of inertia Iz of the frustum of the cone which has a conical depression. The material has a density of 200 kg/m3.
1) The buoyant force acting on the plate is equal to a the mass of the plate times distance of the plate from the free surface b the weight of the plate c the weight of the liquid displaced by the plate 2) The hydrostatic force acting on a circular surface always passes through the center of the circle. True or False 3) Which of the following situation is UNSTABLE? a,b,c?
Block A has a mass of 100 kg and a coefficient friction of 0.30. Determine the friction force acting between A and B.
diameter = 60 cm height = 60 cm The CLOSE cylindrical tank is two-thirds full of water. It is subjected to pressure = 10 kpag. Considering that the tank is to rotate about the axis at the center at 10 rad/s a. What is the pressure at point C? b. What is the pressure at point D?
The two springs are identical, with unstretched length 0.4 m. When the 50-Kg mass is suspended at B, the length of each spring increases to 0.6 m. What is the spring constant K?
A cylindrical tank 2.20 meters in diameter and 15 meters high is filled with liquid Z. Apressure gage at elev. 10m at the side of the tank reads 105 kPa.Another gage at elev. 6m reads 140 kPa. Compute the specific weight of the liquid, density and specific gravity.
A cube is dropped into the cylinder and the water rises. The length of a side of the cube is 3.7 cm. Specific weight of water is 9.81 kN/m3. Find the density of the cube, the specific gravity of the cube. Where is the vertical CG of the cube? Vertical center of buoyancy based on SWL?
Calculate the hydrostatic force and components of the semicylindrical protuberance located at the bottom of the tank. It has a length of 9 feet inward.
The rectangular bin with an inclined gate AB is filled with oil to the depth shown. Determine the resultant force (kN) acting on the inclined side AB. Take density of oil - 900 kg/m^3 x=3.27 a=5.2 m b=30 degrees asap
Find the position of centre of buoyancy for a wooden block of width 3.5 m and depth 1 m, when it floats horizontally in water. The density of wooden block id 850 kg/m3 and its length 7.0 m. *
If each pulley has a mass of 5 kg, what is the mass “M”that will hold the system in equilibrium?Neglect Friction of the pulleys.