Take o,= 120 kPa and o, = 630 kPa Determinethe equivalent state of stress on an element at thesame point that represents the maximum in-planeshear stress at the point.(Figure 1)FigureK 1 of 1Oy400 kPaPart AFind the value of Tmax in-plane-Express your answer to three significant figures and include the appropriate units.µATmax in plane =ValueUnitsSubmitRequest AnswerPart BFind the value of oavgExpress your answer to three significant figures and include the appropriate units.

Answered: Image /qna-images/answer/a7be7c0e-cd7e-42f7-b584-c3b53c4e7c1b.jpg

Answered: 120 kPa and O lent state of stres t…

Engineering

Civil Engineering

120 kPa and O lent state of stres t that represents ss at the point.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical rod AB has a length ? = 80 cm and a diameterof ? = 2 cm. The modulus of elasticity is ? = 200 GPa andyield strength is ?? = 300 MPa. The stress-strain diagram ofthe rod is shown in the left figure. A force ? = 100 kN isapplied to the bar and then fully removed (right figure).Determine the permanent set in the rod.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa
A part’s maximum Von Mises stress and materials are given below. Determine for each of these conditions whether the part is safe or not. Material: Steel, Von Mises Stress: 31000 psi, Static Loading, Ultimate Strength = 80000 psi Material: Polystyrene, Von Mises Stress: 42000 psi, Static Loading, Ultimate Strength = 7500 psi Material: Aluminum, Von Mises Stress: 62000 psi, Repeated Loading, Ultimate Strength = 30000 psi Please clearly show all calculations and reasoning in your computation.
10.24 A concrete canoe in storage is supported by two rope slings, as shown. each sling supports 48lb. The rope has a tensile breaking strength of 252lb. Determine the maximum value of theta if there is to be a factor of safety of 4.0 against breaking.
At the limit of proportionality, a bar 30 mm wide (w) and 12 mm thick (t) elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5 m long. If the Poisson's coefficient of the material is 0.33, determine: (a) the modulus of elasticity. E = ? (b) the variation in width. dw = ? (c) variation in thickness. dt = ?
Consider a cylindrical metal 6 mm in diameter and 50 mm long ispulled in tension. It is known that yield strength and elastic (Young’s) Modulus of thematerial are 200 MPa and 100 GPa, respectively, and its Poisson’s Ratio is 0.3.(a) Determine whether the deformation is elastic or plastic when 6000 N is applied.(b) Calculate specimen elongation (∆l) and reduction in diameter (∆d) when 5000 N isapplied? What are the values ∆l and ∆d when the load is released?(c) If necking occurs at a load of 8850 N, determine the UTS of the metal.(d) Calculate the ductility in terms of % E.L. if the length of the specimen at fracturepoint is 56.0 mm.
Question 1: A 25mm diameter aluminum rod is loaded axially in tension with a load of 100kN. The rod is 4 m in length. Aluminum has a modulus of elasticity of 69GPa and a Poisson’s ratio of 0.35. 1) What is the decrease in diameter of the rod due to the applied load? 2) What is the new length of the rod?
SOM 3.1 Show your complete/correct solution. ( I need detailed solution since there is given answer.) Given answer: Stress in bars AC = 49468.962 psi Stress in bars CB = 8588.361 psi
Show solution. Don't round off initial values, round off final ans only
The rectangular block shown in Figure is subjected to tension within the elastic range. The increase in the length of a is 2 * 10-3in. and the contraction of b is 3.25 * 10-4 in. If the original lengths of a and b were 2 in. and 1 in., respectively, what is Poisson’s ratio for the material of the specimen?
A circular bar of magnesium alloy is 750mm long. The stress-strain diagram for the material is shown in the figure. The bar is loaded in tension to an elongation of 6.0mm, and then the load is removed. (a)What is the permanent set of the bar? (b)If the bar is reloaded, what is the proportional limit? (High: Use the concepts illustrated in figures below)
Note: Give me right solution according to the question. If any data missing assume that. A wheel applies 40 kN load on a semi-infinite elastic space as shown in Figure. The modulus of elasticity of the material is 150 MPa and the Poisson’s ratio is 0.38. Assume the load is applied on the surface as a concentrated force. The vertical deformation at a depth of 500 mm at the centerline of the wheel is most nearly: 0.64 mm 0.07 mm 0.41 mm 0.26 mm