13-14 Rods AC and BC are used to su which the average normal stress can not exceed 150 Mpa What is the force on one tension rod given the assembly is symmetrical? (1kg = 9.81N) C.2.26 kN CS CA 15ed with B.r.se *** 3.1.5€. Sean C-?2 D. 3.92 KN Determine the minimum requirea diameter of each rod. A. 5.77 mm B. 4.38 mm C. 4.08 mm D. 3.10 mm 60 c

13-14 Rods AC and BC are used to su which the average normal stress can not exceed 150 Mpa What is the force on one tension rod given the assembly is symmetrical? (1kg = 9.81N) C.2.26 kN CS CA 15ed with B.r.se *** 3.1.5€. Sean C-?2 D. 3.92 KN Determine the minimum requirea diameter of each rod. A. 5.77 mm B. 4.38 mm C. 4.08 mm D. 3.10 mm 60 c

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The single rope of a cantilever crane supports a load of 200 kN and passes over two pulleys and then vertically down the axis of the crane to the hoisting apparatus. The section AB of the crane is a hollow rectangle. The outside dimensions are 37.5 cm and 75 cm and the material is 2.5 cm thick all round, and the longer dimension is in the direction AB. Calculate the maximum tensile and compressive stresses set up in the section, and locate the position of the neutral axis. (Cambridge) ANSWER: tensile 155 MN/m2, compressive 147 MN/m2; neutral axis 0.365 m from outside of box-section Please show the solution to get the answer.
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).
as fast as you can pleaaaase A beam is used to support a concentrated load of 12 kN and a distributed load (w). The beam has the following restrains: Fixed support at A, a hinge at B and a roller support at C. If the distributed Load w is 6 kN/m and E is known to be 200 GPa, Determine the following: If the supports at A and C were changed to pin supports and the hinge at B was removed. How would the maximum bending stress change? Support your claim with numbers.
For the beam shown, determine the support reactions and draw the stress diagrams.shear and bending moment. EI is constant. Use the force method. I have a correct answer, it is: VA = 44.3 kN (↑); HA = 0 kN; MA = 34.3 kN.m (counterclockwise); VB = 38 kN (↑). I don't know how to get to this result, please show me how to get there step by step
The following beam is supported by three cables AD, BE, and CF. Cables AD and CF are made of steel, and cable BE is made of aluminum. The data is presented in the table. A force P of 125 kN is applied, and the temperature increases by 100°C. Determine: The stress in each cable. Answ: 25.09 MPa, 49.22 MPa. The vertical displacement of the beam. Answ: 1.99E-3 m.
Which of the following is the nearest value for the force at member AC? a. 3.4 kN tension b. 3.4 kN compression c. 1.7kN compression d. 1.7kN tension
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
Determine support reaction at B . Given P=100 Kn L=10 m
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 270 mmBeam height = 375 mmWLL = 14.38 kN/mWDL = 18.41 kN/mSpan of the beam = 8 mPrestressing force = 481 kNeccentricity = 103 mm
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places