14) Indi a) Copper and its alloys do not fail due to cycling loading if the applied stress amplitude is below a certain level. b) Alloys with HCP crystal structure do not fail due to cycling loading if the applied stress amplitude is below a certain level. c) If there exist many slip systems such metals and alloys do not fail due to cycling loading if the applied stress amplitude is below a certain level. d) The practical rule that says there exist a fatigue limit for iron based alloys is not strictly true.

14) Indi a) Copper and its alloys do not fail due to cycling loading if the applied stress amplitude is below a certain level. b) Alloys with HCP crystal structure do not fail due to cycling loading if the applied stress amplitude is below a certain level. c) If there exist many slip systems such metals and alloys do not fail due to cycling loading if the applied stress amplitude is below a certain level. d) The practical rule that says there exist a fatigue limit for iron based alloys is not strictly true.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

strength-of-materials pressure-vessels Maximum shear stress at any point in a thin cylinder of diameter (d) and thickness (t) subjected to an internal fluid pressure (p) is given by-
The degree to which the theoretical value of stress concentration is actually reached is called as
I need the answer as soon as possible
Answer Q(i), (ii) & (iii) explaining detailly each step
16) Which of the following mechanical properties can be measured / calculated from this tensile stress-strain graph of a generic metal alloy? (pick all that apply) a. Poisson's ratio b. Elastic modulus C. Shear modulus d. Flexural modulus e. Fracture toughness 17) Interstitial sites in a FCC lattice are called a. Rhombohedral and cubic b. Cubic and hexagonal C. Monoclinic and triclinic Stress (MPa) 2000 MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0.000 0.020 0.040 Strain 0.060 0.080 d. Tetrahedral and octahedral e. Heterogeneous and homogeneous 18) Traditional photovoltaics rely on which structural feature to separate charge carriers? a. The p-n junction b. The grain boundaries C. The twin boundaries d. The electron-hole pair e. The band gap 19) The process by which lithium ions move in to and out of graphite in a lithium-ion battery is called a. Intercalation b. Stacking C. Precipitation d. Phase combination e. lonization 20) A polymer obtained by the polymerization of two types…
The constant a for a steel material having an ultimate strength of 106.5 ksi is
A single zinc crystal is loaded in tension with the normal to its slip plane at 60° to the tensile axis and the slip direction at 40° to the tensile axis. a) Calculate the resolved shear stress when a tensile stress of0.69 MPa is applied. b) What tensile stress is necessary to reach the critical resolved shear stress of 0.94 MPa?
At an axial load of 20 kN, a 45-mm-wide by 10-mm-thick polyimide polymer bar elongates 3.3 mm while the bar width contracts 0.21 mm. The bar is 240 mm long. At the 20-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= i i i GPa mm
The material returns to its original shape when the load is removed. (A Elastic Limit B Elastic Behavior Limit c) Maximum Limit D D Proportional Limit
Example: the low cycle fatigue of a certain steel is given by life cycle equation-2: (ay/E)=0.005 -0.07 b= -0.08 c= -0.7 a. What is the value of the transition fatigue life, in this case 2 N/when EE - Ep b. What is the total strain amplitude at the transition fatigue life?
After an inspection it is found that a structural ceramic part has no flaws greater than 100 micrometers in size, calculate the maximum service stress (in MPa) available with SiC. Assume that Y= 1
i need the answer quickly