14 - Obtain the center of gravity of the surface area of the constant thickness plane plate in the figure in the (x, y) set given. Dimensions a = 12 m, b = 23 m and r = 3 m, the center of the circle is at the point (2a, 1/2 b). Which of the following is the coordinate of the center of gravity of the plate in the x-axis correct?

14 - Obtain the center of gravity of the surface area of the constant thickness plane plate in the figure in the (x, y) set given. Dimensions a = 12 m, b = 23 m and r = 3 m, the center of the circle is at the point (2a, 1/2 b). Which of the following is the coordinate of the center of gravity of the plate in the x-axis correct?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 85CQ

See similar textbooks

Similar questions

(2) sz The bar ABCD is fixed at A by a pin and supported by two wires as shown in fig. the bar is subjected to aload of 75 kN at D. the relation between the movement of point N BtoDis TSN 36B =2 8D 26B =3 6D 8B =4 6D None of all these 26B = 8D O OOO0O0
2. The beam AB shown is supported at A and B. the beam is loaded with three fixed concentrated loads and an overhead hoist carrying a load W. P1 P2-320 KN. P3-200 KN and W-500 KN A. Find the distance of W from A in meters if the resultant of the external loads is at the midspen B. What is the reaction at A when W is at midspan?
A steel rod is bent to form a mounting bracket. For each of the mounting brackets and loading shown, determine the reactions at A and B. Take L = 230mm, F1 = 6ON, F2 = 130 N, M = 14 N.m *
Classify the structure as statically determinate (Write SD), statically indeterminate (Write only the degree of indeterminacy, i.e. if SI in 2 degree, only write 2) or unstable (Write U). Blank 1
Determine the embedment length of the tension bar around the area of the supporting column. Let h=500mm b= 300mm
A force of F = {6i - 2j + 1k} kN produces amoment of MO = {4i + 5j - 14k} kN ⋅ m about the origin,point O. If the force acts at a point having an x coordinateof x = 1 m, determine the y and z coordinates. Note: Thefigure shows F and MO in an arbitrary position.
The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle Ө0 = 0.75° when the load is applied, as shown in the detail. E = 72 GPa and I = 120 x 106mm4. Determine the following: Reaction at A (kN) Moment at B (kN m) Slope at A in radians Displacement at the application of 200kN load
A 290 N/m light crane rail sits on and is securely fastened to a W400 mm x 67 kg/m crane girder. The girder is simply supported on a span of 9m. Crane wheel loads: V = 80kN, H = 8kN Assume full transfer of lateral load to the top flange of the girder. Girder properties are: A =8580 mm2 d= 400mm tw = 8.5mm bf = 179mm tf =14mm Ix = 2.44 x 108 mm4 Iy = 0.14 x 108 mm4 a) What is the maximum bending stress, fbx (MPa), in the girder? b) What is the maximum bending stress, fby (MPa), in the girder? c) Using the interaction formula, fbx/Fbx + fby/Fby, determine the maximum span of the girder so that the section shall be adequate for the given loads if the allowable stresses are: Fbx = 207 MPa; Fby = 258 MPa.
Taking into account the frame in the illustration below Given E = 200 GPa, I = 2x109 mm4 These loads are applied to the beam Uniformly distributed vertical load of intensity 8 kN/m at member AB Acting 3 meters above the rocker support is a 20 kN point load. The beam is held up by the following: Support in place at point A Support for rockers at Point C Questions 1. Determine the vertical reaction at support A. Ans 35 KN 2. Determine the horizontal reaction at support A. Ans 20 KN3. Determine the Moment reaction at support A. Ans 51 KNm4. Determine the vertical reaction at support C. Ans 37 KN5. Determine the horizontal deflection of point C due to the loads with respect to its original location. Please solve the Question no. 5 and explain.
The simply supported beam consists of a W21 × 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w = 6.5 kips/ft, determine: (a) the beam deflection vA at point A. (b) the beam deflection vC at point C. Assume LAB = 13 ft, LBC = 5 ft, LCD = 5 ft, LDE = 7 ft.
3. Two 10”-15.3 lb channels are welded together as shown in the figure. Find themoment of area of the upper channel about the horizontal centroidal axis xo of the entire section.
The pipe is held in the place bye the vise. if the bolt exerts a force of 300N on the pipe in the direction shown, determine the force FA and FB that the smooth contacts at A and B exert on the pipe