Question 3: 150 m long commercial steel pipe is to convey 30 L/s of oil (s=0.9, p=0.038 N.s/m² from one tank to another (submerged discharge) where the difference in elevation of the free liquid surface is 2 m. The pipe entrance is flush and there is a fully open gate valve in the line. Using only basic scientific calculator, find the diameter theoretically required. Use k=0.19 for fully open pipe or follow the following table (Table 8.3). Flush Valve TABLE 8.3 Values of loss factors for pipe fittings k 10 Fitting Globe valve, wide open Angle valve, wide open Close-return bend ma L, e, Q 5 2.2 10 L/D 350 175 75 60 T Az

Question 3: 150 m long commercial steel pipe is to convey 30 L/s of oil (s=0.9, p=0.038 N.s/m² from one tank to another (submerged discharge) where the difference in elevation of the free liquid surface is 2 m. The pipe entrance is flush and there is a fully open gate valve in the line. Using only basic scientific calculator, find the diameter theoretically required. Use k=0.19 for fully open pipe or follow the following table (Table 8.3). Flush Valve TABLE 8.3 Values of loss factors for pipe fittings k 10 Fitting Globe valve, wide open Angle valve, wide open Close-return bend ma L, e, Q 5 2.2 10 L/D 350 175 75 60 T Az

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.) A 75 mm diameter pipe, 2 m long is just filled with oil (sp. gr. = 0.822) and then capped, and place on horizontal position. It is rotated at 27.5 rad/sec about a vertical axis 0.5 m from one end (outside the pipe). What is the pressure in kPa at the far end of the pipe? Answer: 1865 Kpa Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Topic: hydraulics A pipe carrying oil of specific gravity 0.877 changes in size from 150mm at section 1 and 450mm at section 2. Section 1 3.6m below section 2 and the pressures are 90kPa and 60kPa respectively If the discharge is 150 ht sec determine the head lost and the direction of the flow.
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.
Determine the friction loss if the friction factor is 0.4 and velocity of the flow is 40 m per sec. Given length of the pipe is 20m, inner diameter 0.3m. Use friction loss formula. Using the calculated friction loss, solve for the ffg: a. What is the pressure drop due to the Bernoulli effect as the water goes into a 3.00-cm-diameter nozzle froma 9.00-cm-diameter fire hose while carrying a flow of 40.0 L/s? b. To what maximum height above the nozzle can this water rise? (To actual height will be significantly smaller due to air resistance.)
A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge when the oil level in the tank is 4m above the exit of the pipe. Neglect minor losses, (assume f = 0.12)
Oil (SG=0.82) entering a pump through an 180mm diameter pipe at 35kPa has a flow rate of 0.07 m^3/s. It leaves the pump through a 120mm diameter pipe at 120 kPa. Assuming that the suction and discharge sides of the pump are at the same elevation, find the horsepower delivered to the water by the pump (746 watts = 1 HP). Illustrate the problem and show your complete solution.
a venturi meter having a diameter of 6 in, at the throat is installed in a horizontal 18-in. water main. in a differential gage partly filled with mercury (the remainder of the tube being filled with water) and connected with the meter at the inlet and throat, the mercury column stands 15 in. higher in one leg than the other. what is the discharge through the meter in cubic feet per second: (a.) neglecting friction; (b.) if the loss head between inlet and throat is 1 ft of water? Compute the meter coefficient in (b).
An open cylindrical tank, 2.4 m diameter and 6m tall has 1m of glycerin (Sgglycerin=1.5), 2.5m of water, and 1.5m of oil (Sgoil=0.82). Determine the discharge through the 125mm diameter located at the bottom of the tank. Assume C=0.65
pls answer asap for my hydraulics course. A 30 cm diameter pipe is connected by a reducer to a 10 cm diameter pipe. Points 1 (on the 30 cm diam.) and 2 (on the 10 cm diam.) are along the same elevation. The pressure at 1 is 250 kPa. The flow is 30 liters per second and the energy lost between 1 and 2 is equivalent to 20 kPa. Compute the pressure at 2 if the liquid flowing has a specific gravity of 1.50.
A venturi meter with a throat diameter of 100 mm is fitted in the inclined pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. The venturi meter coefficient is 0.96. Two pressure gauges are fitted at tapping points, one at the throat reads the vacuum pressure of 40 cm of mercury and the other in the inlet pipe 320 mm below the throat is 20.231 N/cm2. If the loss of head in the main and throat is 0.35 times the kinetic head of the pipe, determine2.1 the volume flow rate of oil through the pipe2.2 the difference in level in the two limbs of the mercury manometer if it is connected to the tapping points and connecting pipes are filled with the same oil
The pipe is 25mm with friction factor of 0.022. The second tank is vented. H1=1.4m H2=4.5m H3=1.0m X1=14.9m X2=2.7m Calculate the pressure(kPa) above the gasoline in the first tank that will result in a flowrate of 400 liters/min.
A fluid is flowing in a pipe 20-cm∅ with a mean velocity of 3 m/s. The pressure at the center of the is 35 kPa and the elevation of the pipe above the assumed datum is 5 m. compute the total head, E in meters, if the fluid is:a) Oil (sp.gr. = 0.85)b) Gas (γ = 6.30 N/m3) c) Water Pls include figure for better understanding