150 mm 2.) A timber beam 150 mm wide by 250 mm deep is to be reinforced at the top and bottom by the steel plates 10 mm thick. Assume thatn=15, the beam is to resist a moment of 40 kN.m and the beam details as shown. a.) Which of the following gives the width of the steel plates without exceeding the stress in the wood of 10 MPa. b.) Which of the following gives the width of the steel plates without aNceeding the stress in steel of 120 MPa.

150 mm 2.) A timber beam 150 mm wide by 250 mm deep is to be reinforced at the top and bottom by the steel plates 10 mm thick. Assume thatn=15, the beam is to resist a moment of 40 kN.m and the beam details as shown. a.) Which of the following gives the width of the steel plates without exceeding the stress in the wood of 10 MPa. b.) Which of the following gives the width of the steel plates without aNceeding the stress in steel of 120 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following A. Depth of compression block "a" B. Strength Reduction C. Ultimate moment capacity
The wooden section of the beam is reinforced with two steel plates as shown. Determine the maximum moment M that the beam can support if the allowable stresses for the wood and steel are (sallow)w = 6 MPa, and (sallow)st = 150 MPa, respectively. Take Ew = 10 GPa and Est = 200 GPa.
D) If the diameter of the cross-section of the beam is 500 mm compute for the maxumum shearing stress E) ss
COMPLETE SOLUTION! The 1000kg uniform bar AB is suspended from two cables AC and BD; each cross- section area 400mm2. Find the magnitude P and the location x of the largest additional vertical force that can be applied to the bar. The stresses in AC and BD are limited to 100MPa and 5MPa, respectively.
A simply supported wood beam that is 4.2 m long carries a 38 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 350 mm, a = 105 mm, and c = 15 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. Draw a horizontal line through point H. Use the area above this line to calculate the first moment of area associated with point H.Answer:QH = mm3
Determine the location of neutral axis from the extreme compression fiber.
A hollow circular pole, 6m. thick with 300 mm outside diameter and height of 3 m weighs 150 N/m. The pole is subjected to the following vertical load P= 3KN at an eccentricity e=100mm from the centroid of the section, lateral force H = 0.45 KN at the top of the pole. Note, used combined stresses principle for solving the ff. questions. A. Determine the maximum compressive stress at the base due to the loads. B. If the hollow pole is replaced by a solid wood pole of 250 mm diameter, determine the maximum shear stress. C. Determine the maximum tensile stress at the base due to the loads.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a – a is located at x = 0.7 m from B. (a) At section a – a, determine the magnitude of the shear stress in the beam at point H. (b) At section a – a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length
The single rope of a cantilever crane supports a load of 200 kN and passes over two pulleys and then vertically down the axis of the crane to the hoisting apparatus. The section AB of the crane is a hollow rectangle. The outside dimensions are 37.5 cm and 75 cm and the material is 2.5 cm thick all round, and the longer dimension is in the direction AB. Calculate the maximum tensile and compressive stresses set up in the section, and locate the position of the neutral axis. (Cambridge) ANSWER: tensile 155 MN/m2, compressive 147 MN/m2; neutral axis 0.365 m from outside of box-section Please show the solution to get the answer.
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Calculate also the allowable force in rod 1. Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
Design the beam using the Working stress diagram to resist the loads. Take fc = 10 MPa, fs = 120 MPa, n = 12, bar diameter = 20 mm. Take b = d/2.