17. For the network of Fig. 12.74: a. Determine the mathematical expressions for the cur- rent iz and the voltage V when the switch is closed. b. Repeat part (a) if the switch is opened after a period of five time constants has passed. c. Sketch the waveforms of parts (a) and (b) on the same set of axes. R1 10 kf 20 V R10 kn 10 mH V FIG. 12.74

17. For the network of Fig. 12.74: a. Determine the mathematical expressions for the cur- rent iz and the voltage V when the switch is closed. b. Repeat part (a) if the switch is opened after a period of five time constants has passed. c. Sketch the waveforms of parts (a) and (b) on the same set of axes. R1 10 kf 20 V R10 kn 10 mH V FIG. 12.74

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1-Alternators can be overloaded by 10 percentage for 10-15 minutes, this a. Steady state voltage stability will get affected b. may reduce the stability limit c. may disturb Nose point d. may lose Angular stability 2-Often, the network is referred as an infinite bus when a change in input mechanical power or in field excitation to the unit does not cause an appreciable change in a. system frequency or terminal voltage b. system frequency alone c. system frequency and terminal voltage d. Total production cost
Suppose a power system consists of two isolated regions: a western region and an eastern region. Five units have been committed to supply 3090 MW as shown below. The two systems are separated by a transmission line that can handle a maximum transfer of 550 MW in either direction. Calculate the spinning reserve for the overall system and for eachregion.
q21- Electrodynamic meters can measure ac signals only. True False
Find the a) time constant, and b) settling time of a first order system with a rise time of 44 ms.
For a Natural Gas based Power Generation unit, which of the following cannot be an input quantity for plotting input-Ouiput characteristics? a. m^3 /h b. $/m^3 C. MBtu /h d. $/h
The Karnaugh map of v
1)an instrument that graphically displays measurements of Voltage value, frequency and phase difference in Electrical and electronic circuits on a digital or analog screen .......................’tour. 2)an instrument that measures the electrical power attracted by receivers in correct and alternating current circuits.....................’dir. What should come to the dotted line?
Answer: y11=75.77mS , y12=y21=-30.3mS , y22=45.47mS
Transmission line with a load Zl = 100 + i80 ohm with characteristic impedance of Z0 = 5 ohm is designed. The transmission line operates at 100 MHz, where is matched with a shunt single- stub tuner. a)Calculate the stub positions. b)Calculate the stub length where open circuit stub is used. c) Calculate the stub length where short circuit stub is used.
. At a 12.47 kV (line to line) distribution system the communication interference (CI) was observed due to 5% of 5th harmonic currents generated by a 3000 kVA arc furnace. In order to avoid CI it is required to convert an existing 600 kVAr capacitor to 5th harmonic filter considering the total kVAr should not exceed 135%. Calculate the following: (i) Capacitor reactance (ii) Reactance of the series reactor (iii) Fundamental frequency current (iv) 5th harmonic frequency current (v) Tuned frequency voltage (vi) Total rms current (vii) Fundamental frequency voltage (viii) Voltage (rms) across the capacitor bank (ix) Check whether the filter kVAr rating is within limit? (x) Comment how the existing capacitor bank is converted to filter
Company Y would like to have a new installation transmission line to open a small new city consist of 300 MW with 0.85 power factor lagging at full load. The new transmission line required 132 kV with 124.274 miles long. All the elements needed for the new transmission line is listed in table shown in the picture. You are required to model the transmission line and analysed the performance of the new transmission lines in terms of voltage regulation and efficiency. Note that the frequency used is 50 Hz.
Design a shunt stub that will match a 50+j50 ohm load into a 100 ohm transmission line. Answer text