17. Theof a bonded abrasive is a measure of its bond strength.A. structure B. grade C. grain size18.are used for clamping irregularly shaped workpieces.A. Three-jaw chucksC. MandrelsB. Face platesD. Follow rests19. In bending operation of a piece of flat metal sheet. The final bendangle after springback isthan the angle to which the part wasbent.A. largerB. smallerC. not sure20. Machining is a general term describing a group of processes thatconsist of the of material and modification of the surfaces of aworkpiece after it has been produced by various methods.A. additionB. deformationC. changing D. removal

Abrasive grains, fillers, and bonding materials make up bonded abrasives. Resin, rubber, glass, and…

Answered: 17. The of a bonded abrasive is a me

Engineering

Mechanical Engineering

17. The of a bonded abrasive is a me

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.4: Manual Lathe Threading

Problem 15RQ: What type of thread is machined on a tapered diameter and is used to create leak-proof joints?

See similar textbooks

Related questions

Q: Why Dielectric flued is used in EDM ?

A: EDM - Electric discharge machiining. It is type of non traditional machining. Mechanism: Melting and…

Q: ing With Reference

A: To Differentiate : The gear hobbling and Gear shaping with Reference to various relative motion and…

Q: Talks about grinding, and Grinding Lathe Tool Bits. Explain properly.

Q: Material removal rate is increased in which of the following grinding processes: Creep feed grinding…

A: Option (a) is correct. Creep feed grinding

Q: Explain the material and equipment for grinding lathe tool bits.

A: lathe tool bit : A tool bit is a like non rotary cutting tools metal used in machines like lathe…

Q: 9) The number of impacts on the workpiece · by abrasive grits in each cycle is dependent upon the O…

Q: 19)With an increase in abrasive particle size in AJM

A: Solution:

Q: 11)lncrease in abrasive grain size in USM results in

A: After increasing grain size of USM Higher MRR but lower surface finishing Option b is absolutely…

Q: 5.a) Derive a quantitative relationship for abrasive wear b) Explain the merits and demerits of…

A: Given Friction To find Quantitative relationship for abrasive wear Advantage and disadvantage of…

Q: What material would work best for milling abrasive material? O High speed steel Carbide

A: Some materials that are used as abrasives include Diamond most often used in ceramic grinding and…

Q: Explain the steps in making a T-nuts

A: Milling is a type of machining that involves advancing a cutter into a workpiece and removing…

Q: Relation between shear stress and shear rate for a tooth paste is Curve statrting from origin…

A: For a Newtonian fluid, the shear stress will be proportional to shear strain. So, for Newtonian…

Q: in a cylindrical grinding of a long shaft, the work piece is often supported by the?

A: Grinding is the process of surface finish in which material is removed from surface of a work by the…

Q: suitable answer for the following questions depending on your conclusion:(Five only) Why are LBM and…

A: Disclaimer: Since you have posted a question with multiple subparts we will solve the first three…

Q: 8) In AWJM, the mixing efficiency of both water and abrasives were maximum in

A: Answer is Multiple jets central feed nozzle.

Q: Explain the difference between Open Structured and Dense Structured Grinding Wheels

A: It is required to differentiate between open structure and dense structure grinding wheel

Q: Name 2 adverse effects of allowing the workpiece to become too hot in grinding. 12) Name 2 reasons…

A: Effect of allowing the work piece to become too hot in grinding: the adverse effects are given below…

Q: 17)ln which process, Al203 can be used as an abrasive grain

Q: Types of grain action in grinding that encounter deformed surface without removing any material is…

A: Plowing- Grit can penetrate to the surface(not far enough to cut) but can not perform cutting.The…

Q: Corundum is an example of natural abrasive material used in manufacturing grinding. Eelect one:

A: Grinding is a machining process in which material is removed by a rotating wheel.

Q: The term deep grinding refers to which .17 ?one of the following

Q: The number of teeth of a spur gear is 50 and it rotates at 250 rpm What will be a circular pitch and…

A: Data given- T = 50 N = 250 rpm m = 5

Q: : How is the size of the abrasive grain chosen?

Q: 13) Manufacturers are designing grinding spindles to turn at higher and higher speeds. What is the…

A: Manufacturers are designing grinding spindles to turn at higher and higher speeds. The main reason…

Q: Define trueing and creep feed grinding.

A: Truing:-Truing is the process of changing the shape of the grinding wheel as it is become worm from…

Q: 13)Bonded magnetic abrasives in MAF process results in O Higher removal rates Poorer surface finish…

A: Bonded magnetic abrasive particles are produces by using the sintering process on ferromagnetic…

Q: Estimate the relative cost ot grinding a steel part to a tolerance of +0.0005 in versus turning it…

Q: Which of the following are the grinding types?

A: Which of the following are the grinding types. Answer: C) All

Q: ). What do you mean by FMS and what are its applications?

Q: What are the two forms of abrasives used in benchwork?

A: Two types of abrasives are employed in benchwork: Abrasive paper is one type of abrasive coating…

Q: uggest TWO (2) advantages of EDM as compared to Chemical Milling.

Q: Q4: State the advantage of electro polishing over mechanical polishing.

A: This question is based on the concept of electropolishing from mechanical manufacturing engineering.

Q: The advantage of an independent chuck is that it is easy to work with. Select one: True False

A: A chuck is a machine component that is used to hold the workpiece in the predefined position in such…

Q: Is of a uniform flow filed, a d-

A: False

Q: Draw a table to describe the differences between jigs and fixtures.

A: we are differentiating jigs and fixture on the bases of : definition elements construction Use…

Q: 6. If you were asked to design a gear from the same material. What would be the maximum thickness…

A: Case-solidifying is viewed as thermomechanical treatment to change the surface properties of stuff…

Q: Outline the principle of Electro Discharge Machining (EDM) and its scope of use in industry.

Q: What is abrasion resistance testing?

A: Abrasion resistance testing is used to test the abrasive resistance of solid materials. Materials…

Q: Q1: How is the size of the abrasive grain chosen? Q3: How does superfinishing differ from honing?

A: Given question: How is the size of abrasive grain chosen? How does superfinishing differ from…

Q: Calculate the RPM for drilling at 600 SFM and feed rate (in/min) for a chip load of .010 (in/rev)…

Q: 5. Types of Grinding Wheel Machines and their outputs. (atleast 3)

A: Types of grinding machine: Floor or bench grinder: This is a small type of machine used in the…

Q: Write the applications of bench grinding machines. ( type by Keyboard two pages at least )

A: A bench grinder is a portable grinder that is usually seen in most metalworking shops. Workpiece is…

Question

17. The
of a bonded abrasive is a measure of its bond strength.
A. structure B. grade C. grain size
18.
are used for clamping irregularly shaped workpieces.
A. Three-jaw chucks
C. Mandrels
B. Face plates
D. Follow rests
19. In bending operation of a piece of flat metal sheet. The final bend
angle after springback is
than the angle to which the part was
bent.
A. larger
B. smaller
C. not sure
20. Machining is a general term describing a group of processes that
consist of the of material and modification of the surfaces of a
workpiece after it has been produced by various methods.
A. addition
B. deformation
C. changing D. removal

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

8/ Identify the part of a lathe machine which is mainly used to cut external threads. Head stock Lead screw Tailstock Bed
By hand solve??
A lathe mandrel is a hardened and tempered steel work-holding device.it is used for the further machining of a workpiece between centers after it has been bored or reamed while held in a chuck . The mandrel is ground to a taper of (a) 0.008 (b)0.006 (c) 0.005 (d) 0.007] inch per foot
What is Lathe Machine? Mention three lath operations with aid of clear sketches.
Identify and explain the method of milling process in which the stresses on the teeth is maximum at the end of the cut with neat diagram.
What type of thread is machined on a tapered diameter and is used to create leak-proof joints?
What are the process of taper turning? Typewritten please:)
Differentiate a lathe machine into a shaper machine in terms of operating principle
Correctly solve and by hand solve ?????
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
gearing arrangement suitable for the given application is.
What must be known to use the compound-rest taper turning method?