2-13. The force acting on the gear tooth is F= 20 lb. Resolve this force into two components acting along the lines aa and bb. b F. 80°- 60° a Probs. 2-13/14

Q: Determine the magnitude of the projection of force F = 600 N along the u axis.

A:

Q: 3. Determine the moment of the 50-N force (a) about point O and (b) about point C y, mm +C (0, 25) В…

A: To find moment about point O and C

Q: Determine the internal shear force at point D in the simply supported beam. Point D is located just…

A:

Q: 5.01f the built-up beam is subjected to an internal moment of M 75 kNm, determine the amount of this…

A:

Q: Given: b= 300mm; d= 375mm; d’= 65mm; As’=2D25; As= 6D25 (two layers); fc’=28MPa and fy = 345MPa.…

A: A section is the compression member where the effect of loading results in inward direction load by…

Q: 11. Find the absolute value of the force in the member DC of the frame shown below. If the force F1…

A: The given figure is shown below:

Q: For the load group and influence line shown, P₁ = 8 kips, P2 = 32 kips, P3 = 32 kips, a = 14', and b…

A:

Q: Determine the internal shear and moment in the beam as a function of x throughout the beam. x is…

A:

Q: Force F acts on the frame such that its component acting along member AB is 650 lb, directed from B…

A:

Q: Draw the shear, moment, elastic curve, and axial diagram. 1SP (6) P (6/4) 0-8P (b/ft) 2ft 2ft 2件

A:

Q: -60 and F- 450 N, determine the magnitude of the sukant force and its direction, measured…

A: To find resultant and it's direction

Q: 2. 4KN B 5m 3KN/m 60° D- 5m 2m

A:

Q: e/ Drew Shear and bending moment dygram? be KN 20KN 3 m 2m

A: Calculation of reactions -RA+RB=12×3×60+20×4+20RA+RB=190      eq 1

Q: 4. Internal hinge at C A 10 kN/m B 6 m 2 m IC 12 kN D 2 m 2 m E

A:

Q: Express the internal shear in the given beam as a function of x. Determine the shear at the…

A:

Q: Determine the internal shear and moment in the beam as a function of x throughout the beam. x is…

A:

Q: The ends of the triangular plate are subjected to three couples. Given that F1= 600 N, F2 = 255 N,…

A: Given: The value of F1 is 600 N. The value of F2 is 255 N. The angle α is 50o. The resultant couple…

Q: 13not P 100 N C. 30 20 F= 80 N

A: Magnitude of resultant R = F12+F22+ 2*F1*F2*cos(θ) Given that : angle between two forces = 50°…

Q: 6000mm 6000mm X kN w A Y kN 6000mm В C

A:

Q: 2 kip/it 30 kip-ft B A- -5 ft- -5 ft- -5 ft-

A: Solution: Consider the diagram  ∑Fy=0Ay+By=2×5Ay+By=10 kipTaking the moment  about point…

Q: it's to the right and negative if it's to the left. Determine the vertical reaction (kN) of the…

A:

Q: -100 N/m N-m Im 120 A 2m 1B 4m के с Draw the shear and moment diagram R₂ E

A:

Q: Find the internal force system acting on section 3 for the pin-connected frame. 240 N 0.3 m 240 N0…

A: To find internal force at point 3

Q: Draw the Vand M diagram of the given beam. Indicate the degree and the maximum shear and moment…

A: Given. There is a one side over hang beam given in the question.  Our aim is to determine the…

Q: Determine the shear value (kN) when x = 3m from the left side of the beam where: L = 5.9 m; Wo = 128…

A: step 1-

Q: 3. Determine the internal normal force, shear force, and bending moment at point B. 8 kN/m 1m- Im- -…

A: Given,  Span of the beam = 5m A load of 24KN At point D, is At an inclination of 45° to the…

Q: D + 7 X₁ 2m M₁ 3m M2 2m X2 P₁ P₂| 2m X

A: A loaded cantilever beam is given and it has been asked to determine shear force and moment in…

Q: Determine the shear and moment throughout the beam as a function of x. 7 kN 12 kN-m 2 m 2m m Fig. Ql

A: Solution; Firstly,  The moment at point B, RA+RB=7 KN∑MB=0RA×8-7×6 +12=0⇒RA=7-3.75…

Q: *2-16. Force F acts on the frame such that its component acting along member AB is 650 lb. directed…

A:

Q: 9-35. Determine the slope and displacement at point B. Assume the support at A is a pin and C is a…

A:

Q: The 100lb force Q is applied perpendicular to the section DE of the be the moment of Q about point D…

A:

Q: Test II. Draw the shear, moment, elastic curve, and axial diagram of the beam. 5m 6.6W (kN/m) 5m…

A:

Q: Thecable of length 15m supports the forces W1 = W2 = W at B and C. (a) Derive the simultaneous…

A: Following is the given information:The cable of length 15m supports the forces W1 = W2 = W at B and…

Q: %3D What is the Maximum moment in kN-m. Given: W = 10, a = 2, b = 6, and P = 50. PkN a m W KN'm b m…

A:

Q: The rigid beam is supported by three 25 mm diameter steel rods with E=200 Gpa. If the rigid beam…

A:

Q: Determine the shear value (kN) when x = 1.2m from the left side of the beam where: L = 5.9 m; Wo =…

A: Given data Wo=128 KN/m L=5.9 m X=1.2 m from left end First of all we will find the reaction at Right…

Q: Determine the magnitude of the pin force at C given  θ = 18° and P = 57 lbs.

A:

Q: F4-10. Determine the internal shear and moment in the beam as a function of x throughout the beam. 5…

A: Given -

Q: C). If wheel D rotates with an angular velocity of op=6 rad/s, determine the angular velocity of the…

A:

Q: Determine the internal force and shear force, and the bending moment in the beam at Points C and D.…

A: Given  The beam is shown in which at joint A there is a pin joint, so the components are horizontal…

Q: Min kN.m A w in kN/m 3 m B -4 m C

A:

Q: Situation #2 The rigid bar BC is Supported by he steel rod AC 4css- sectional area 180mm". Find the…

A:

Q: Determine the shear value when x = 5m (from the left) for the beam shown Where: P1 = 52kN; P2 = 42…

A: Determine the shear value when x = 5m (from the left)  for the beam

Q: Find the force in member BD. 20 KN F 10 KN OD00 20 KN 4.0000 0000

A:

Q: For the load group and influence line shown, P1 = 32 kips, P2 = 32 kips, P3 = 8 kips, a = 14', and b…

A: you can clearly understand if you follow the below solution

Q: AB 1.5m gokN CALCULATE THE SHEAR FORCE AND BENDING MOMENT

A: shear force diagram throughout the section

Q: O2 A |B C| 1.5 m--1.5 m 1.5 m -|

A:

Q: H-W:_ Ⓒ Analyize the beam to find reactions of draw B.HD support C settles by 5mmd ; S. D. M. using…

A: