4. 4) The hydraulic cylinder D extends, moves the rigid rod ABC, and causes thecollar A to move with velocity and acceleration both to the left. If the dimensions 1= 1.1 ft, and 2 = 2.3 ft, VA = 4.7 ft/s, aa = 2.7 ft/s², and the angle 0 = 25°, determinethe angular acceleration (in rad/s2) of rod ABC. Negative sign must be included if theangular acceleration is clockwise. Please pay attention: the numbers may changesince they are randomized. Your answer must include 2 places after the decimalpoint.%3D12DаYour Answer:Answer

l1=1.1ftl2=2.3ftvA=4.7ft/saA=2.7ft/s2θ=25° To-Find:- Angular acceleration=?

Answered: 2 = 2.3 ft, VA = 4.7 ft/s, aa = 2.7…

Engineering

Mechanical Engineering

2 = 2.3 ft, VA = 4.7 ft/s, aa = 2.7 ft/s2, and the a cceleration (in rad/s2) of rod ABC. Negative sign

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.47P: A rifle at A is fired at a target at B. If the speed of the bullet is 1400 ft/s, determine the...

See similar textbooks

Related questions

Q: A carbonate whole core 700 cc is placed in cell two of a Boyles Law device. Each of the cells has a…

A: According to the given details provided.

Q: 4 kg block of steel initially at 447 °C is dropped into an insulated tank that contains 20 kg of…

Q: A hydraulic lift system utilizes two 5 in diameter cylinders. Workers must determine how much the…

A: The capability of the lift can be calculated easily using the formula given below as- F=PA where, F…

Q: Given the reference system, determine the coordinate of the centroid Ycg of the symmetrical plane…

Q: A crate of mass 68 kg is pushed along a floor with a force of 30-0 N for a distance of 7.2 m.…

A: Given data : A work done is product of force and displacement Force is represented by F Distance…

Q: DO-1 A block of mass m = 1.75 kg is connected to a spring with a force constant k = 575 N/m. The…

Q: A non-uniform rod of length L has a linear mass density of 1 = kx² where is k some constant. %3D…

Q: ncurrent when their lines of action meet in .A one point .B two points .C three points .D four…

A: Force system 1. Coplanar and Non Coplanar 2. Concurrent and Non Concurrent. 3. Collinear and non…

Q: A triangular lamina is immersed vertically in water in such a way that its 6m wide horizontal base…

Q: A 5-m rod having a uniform cross-sectional area of 1000 sq.mm. is secured between two walls 5…

Q: In an air-conditioning unit 3.5 m3/s air at 27°C dry-bulb temperature, 21°C wet-bulb temperature,…

Q: The resultant of two forces P and Q (such that P > Q) acting along the same straight line, but in…

Q: bar respectively, and AF = 15. Calculate: (i) Throat diameter of the carburetor. (ii) Fuel orifice…

Q: What revision is this part on? 2. How many dimensions are expressed using the limit method? 3.…

A: First of all, the given engineering detailed drawing is given for the assembly of Bonnet Sleeve…

Q: (Find the moment of force when ( F=60 KN , d=5.5 m -37 .A 320KN.m .B 310KN.m .c 330N.m .D 330KN.m

Q: A 20 °C water flows to 50cmx60cm flat plate with velocity of 3m/s . The flat plate surface…

Q: xl: Find the moment of inertia about the x-axis of a thin plate bounded y the curve x = y? and x =…

Q: Answer in a brief and concise essay. Why do we need to study the mechanical properties of a metal?

A: Study of mechanical properties of metals is a must for technological advancement. Mechanical…

Q: Briefly describe two industry applications of robotics.

Q: (Determine the (f_x ) when force 90 N and angle 50° on the axis (Y .A 68N .B 68.94lb .C 69N .D…

Q: 4 kg block of steel initially at 447 °C is dropped into an insulated tank that contains 20 kg of…

Q: A 4 2 que s R. AB vク 42 B o-

Q: 600 r/min, driving a gear of cast-iron with a gear ratic 3. The face width is 70 mm and the tooth…

Q: 20 kN/ 25.5f 1. DRAO Hhe shean and A Sm 4m moment diagnom

A: Shear and bending moment diagrams are analytical tools that are used in conjunction with structural…

Q: Need asap... A potential off-shore wind site will have turbines 70m above a lake. Average wind…

A: Given data The average wind velocity is:V1=5m/s The height is:h1=13 m The surface roughness…

Q: Hand Boiler Mechanics

A: A hand boiler is a glass toy filled with ethyl alcohol. The boiler is made out of a twisting…

Q: Explain, with examples, the effect of shear forces on Newtonian and non-Newtonian fluids.

A: Newtonian fluid: The fluids which obey the newtons law of viscocity are known as newtonian fluid.…

Q: The specific surface energy for aluminum oxide is 0.90 N/m, and the elastic modulus is 393 GPa. The…

Q: Determine the endurance limit of the material with a force 30 lbs led to a facture after 105…

A: given; endurance strength(e1)=?at load(P1)=30lbsendurance strength(e2)=55000psiat load(P2)=25lbs

Q: Determine the values of the stress in the steel bar as shown in the figure below when the…

A: Find the stress and force in the bar.

Q: Draw the relationship between Reynolds number and flow velocity on logarithmic paper ? flow Reynolds…

A: Given data

Q: How does point defect affects the property of a material?

A: To find : How does point defect affects the property of a material

Q: Figure below shows the single degree of freedom control surface/actuator system. The control surface…

A: Given Data : J=30kg/m2K=3000 N/MC=630 N-S/Ma=0.2 md=1mt=0.018 secMoment about point…

Q: Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20…

A: Given: speed of the water→V=5 ms Diameter of the tube→D=2.5 Cm=0.025 m So characterictic length for…

Q: Find modulus of elasticity Stress=30 Pa Strain=0.5

A: Given data : Stress=σ Strain=ε To find : Modulus of elasticity

Q: Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X)

Q: DO-1 A block of mass m= 1.75 kg is connected to a spring with a force constant k = 575 N/m. The…

Q: Discuss which technique is most sensitive to locate the boron? How is the 'local composition…

A: a) Boron (B) can be evaluated utilizing spectrometric and colorimetric techniques. Inductively…

Q: Suppose the pump as shown in the figure is operating at free delivery conditions. The pipe, both…

Q: What company specification number is given to the material for this part? 2. What is the revision…

A: Engg drawing is a technical drawing that is used to transfer the information from the design to the…

Q: ] Caleulate the work raguisedto be done to stop + so km/n ! ot 2000 kg mouing t velboity COY

A: Given data : Velocity (V)=80 km/h Mass (m)=2000 kg To find : Work done

Q: In an Internal Combustion Engine, How to determine its power output? How to determine the…

A: Given questions are: How to determine its power output? How to determine the efficiency of internal…

Q: Given the beam cross-section provided below, determine the maximum allowable bending moment that…

Q: Problem 3: Calculate the maximum shear stress in the following beam section due to an internal shear…

A: Find the maximum shear stress .

Q: Please compute the bmep of an engine when the output is 450 hp, 2300 rpm, bore and stroke are each…

A: Power output, W= 450 hp= 450(33000) foot pounds per minute= 14850000 foot pounds per minute Speed,…

Q: МАТCHING COLUMN A COLUMN B NUMBER a. Plain carbon steel with 0.4 wt% carbon 1. Arrhenius Equation b.…

A: Steel is an alloy of iron with certain amount of carbon alloyed to improve its strength &…

Q: 12 w The unit of Time in U.S. units is

A: To select the correct option.

Q: 5.9-4/ A circular pole is subjected to linearly vary- ing distributed force with maximum intensity…

Q: The roof of a house consists of a 0.70-ft-thick concrete slab (k = 3 W/m · °C) that is 18 m wide and…

Q: Determine the moments of inertia Ix (mm 4 ) and Iy (mm 4 ) in relation to the reference system in…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

4. 4) The hydraulic cylinder D extends, moves the rigid rod ABC, and causes the
collar A to move with velocity and acceleration both to the left. If the dimensions 1
= 1.1 ft, and 2 = 2.3 ft, VA = 4.7 ft/s, aa = 2.7 ft/s², and the angle 0 = 25°, determine
the angular acceleration (in rad/s2) of rod ABC. Negative sign must be included if the
angular acceleration is clockwise. Please pay attention: the numbers may change
since they are randomized. Your answer must include 2 places after the decimal
point.
%3D
12
D
а
Your Answer:
Answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given-Data:-

VIEW

Step 2 FBD

VIEW

Step 3 Calculations:-

VIEW

Step 4 Final-Answer:-

VIEW

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At the moment shown in the figure, it is known that the rod in the vertical direction moves downward with a speed of v=0.8 m/s ederken and has an acceleration = 1.2 m/s2 upward. At this moment in question: a. The angular velocity of the AB rod, b. Bis the speed of the sliding bearing. c. The angular acceleration of the AB rod, d. Find the acceleration of B sliding bearing. Note: Take the R as 0.4m.
The homogeneous bars have a mass as follows: bar AC has a mass of 7 kg, bar ABhas a mass of 10 kg, and rod BD has a mass of 2 kg. In the drawn position, therod AC has an angular velocity of 4 rad/s and an angular acceleration of 2 rad/s2, both clockwise.Determine the magnitude of the moment M acting on the member AC. Give all the equations neededto solve this question without calculating it
Find: friction force between the spool and the ground. and the UNIT of measurement of the acceleration of the mass center of the spool
The equatorial radius of the earth is 2.0925(10^7 ) ft, and the polar radius is 2.0856(10^7) ft. Determine the gravitational acceleration g at the two locations.
Five masses A, B, C , D and E are attached to a shaft and revolve in the different planes . The masses(B,C and D) are 60 kg, 50 kg, 70 kg . Their radius of rotations are 0. 5m. The angular position of the masses (B, C and D) are 600 , 900 and 2100 from mass A. Planes B,C,D and E 60cm ,120cm,200 cm,225cm from mass A Find the magnitude and position of the balancing mass for (A and E) ?
Plot the earths gravitational acceleration g(m/s2) against the height h (km) above the surface of the earth.
An airplane is moving due west at a speed of 100 mi/hr. The propeller blades is 5 ft. long (radius of blades rotation) and turning 1800 RPM clockwise when viewed from the front. Determine: (a) the propeller velocity at the instant when it is vertically above the axis of propellers rotation, (in ft/sec.) and (b) the magnitude and position of the vector resultant of the propellers. (ft/sec. and degrees).
At the top A of the vehicle moving along line AC in the figureIts speed is 30 m / sec and its weight is 9 kN.Tool radius of curvature 40The reaction force to the tires when reaching point B, which is m,and so that the tires do not separate from the asphalt when it reaches point CWhat should be the radius of curvature of point C? (hA = 6 m andhC = 9 m)
A tire 0.400 m in radius rotates at a constant rate of 170 rev/min. Find the speed of a small stone lodged in the tread of the tire (on its outer edge). (Hint: In one revolution, the stone travels a distance equal to the circumference of its path, 2?r.)____m/sWhat is the acceleration of the stone?_____m/s2 away from the center of the path? tangent to the path? toward the center of the path?
A wheel and a connected pulley are rotating around a fixed shaft "O" and driven by a belt. At a specific moment, the velocity of point "A" on the belt is 0.6 m/s, and its acceleration is 2 m/s², both in the directions shown in the diagram. Calculate the magnitude of the total acceleration of point "B" on the wheel at this moment.
The point P moves along a circular path with radius R. Show that the magnitude of its velocity
Prove the relation that Hammer blow = ± mb x r*x ω2 where mb = Balancing mass placed at a radius of r* and ω= angular speed of the crank.