22020A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to aninternal pressure of 10 MPa and a torque of 1000 N.m. Draw a stress element showingthe initial stresses. Calculate the principal stresses and the maximum shear stress.

Answered: Image /qna-images/answer/a6183953-a2b3-416a-8ce8-ca61c611055e.jpg

Answered: 2 20 20 A thin cylinder of 100 mm…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure of 10 MPa and a torque of 2000 N.m. 1. Draw a stress element showing the initial stresses. 2. Calculate the principal stresses and the maximum shear stress.
A 6-inch diameter pulley mounted on a 2-inch shaft as shown transmits 9 kW at 1000 rpm. What is the combined stress acting on the shaft?
show formula and calculation as fast as , don't hold the question for longer time. 1) The 2.3-in.-diameter drive shaft AB on the helicopter in (Figure 1) is subjected to an axial tension of 10 000 lb and a torque of 345 lb⋅ft. Determine the principal stresses and the maximum in-plane shear stress that act at a point on the surface of the shaft.
A 180 mm diameter ship’s shaft rotates as 450 rpm and transmits 5 MW of power. The propeller causes an axial compression in the shaft of 1750 kN. Sketch the stress element on the shaft showing the three possible stress states. Hence, calculate for the position of maximum stress: 4.1 Principal stress on the shaft. 4.2 Maximum shear stress on the shaft. 4.3 The angle of maximum shear stress relative to the XY plane.
Calculate the principle stresses and the maximum shear stress.
Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.
A rod of square 30x 30mm^2 cross-section subject to a compressive axial force of 72kN and a twisting moment of 168.5N.m. Calculate the principal stresses and the maximum shear stress atthemostcritical point in the rod.
The thickness of the bracket is 0.75 in. Draw a neat Mohr's circle 3 kips for the state of stress at point K, and use the Mohr's circle to determine 30 K. 2.5 in. (a) the principal stresses at K, (b) the maximum in-plane shear stress and average normal 2 in. 5 in: stress at K. Sketch the answers on correctly rotated elements.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

2 20 20 A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure of 10 MPa and a torque of 1000 N.m. Draw a stress element showing the initial stresses. Calculate the principal stresses and the maximum shear stress.