2-46. The three concurrent forces acting on the screw eye produce a resultant force Fg 0. If F F, and F, is to be 90 from F, as shown, determine the required magnitude of Fs expressed in terms of F1 and the angle 0. 60 30 F.

2-46. The three concurrent forces acting on the screw eye produce a resultant force Fg 0. If F F, and F, is to be 90 from F, as shown, determine the required magnitude of Fs expressed in terms of F1 and the angle 0. 60 30 F.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.50P: The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of...

See similar textbooks

Related questions

Q: 2-55. Determine the magnitude of force F so that the resultant force of the three forces is as small…

Q: F2-5. The force F = 450 lb acts on the frame. Resolve this force into components acting along…

A: The provided force is shown below.

Q: F2-5. The force F = 450 lb acts on the frame. Resolve this force into components acting along…

A: givenforce F=450lb

Q: 4 - The horizontal component of the force (F ) is ( 60 N ) to the right through the original point .…

Q: 2-3. Determine the magnitude of the resultant force FR = F1 + F2 and its direction, measured…

Q: 2-79. The mast is subjected to the three forces shown. Deterrne the coordinate direction angles…

A: Given, F2 = -200 k N F3 = -300 j N

Q: 2-6. If the tension in the cable is 400 N, determine the magnitude and direction of the resultant…

A: Given Data: The value of force F1 = 400 N. The value of force F2 = 400 N. The angle between the two…

Q: •2-1. If e 30° and T 6 kN, determine the magnitude of the resultant force acting on the eyebolt and…

Q: 2-9. If the resultant force acting on the support is to be 1200 lb, directed horizontally to the…

Q: 2-1. Ife = 30° and T = 6 kN, determine the magnitudi f the resultant force acting on the eyebolt and…

Q: F2-5. The force F = 450 lb acts on the frame. Resolve this force into components acting along…

Q: F2-31. Determine the magnitudes of the components of the force F = 56 N acting along and…

Q: *2-88. Determine the magnitude of the projected component of force FAR acting along the z axis. Fлс…

A: Given: The force FAB = 3.5 kN. The force FAC = 3 kN.

Q: 2-7. Determine the magnitude of the resultant force FR = F, + F2 and its direction measured…

A: Solution: Sum of the forces along the horizontal axis is given by,…

Q: QI. The three concurrent forces acting on the screw eye produce a resultant force F = 0. If F2= 0.8…

Q: *2-84. If the force F = 100 N lies in the plane DBEC, which is parallel to the x-z plane, and makes…

A: The coordinates of the required points are: The position vector of the point B with respect to…

Q: *2-96. The tower is held in place by three cables. If the force of each cable acting on the tower is…

A: Givenx=20my=15m

Q: 2-46. The three concurrent forces acting on the screw c produce a resultant force Fg 0. If F, F, and…

A: Given-Data:- FR=0 F2=2/3 F1 To-Find:- The magnitude of F3 and angle

Q: The line of action of the 2000-lb force runs through the points A and B as shown in the figure.…

A: Given F=2000lb

Q: •2-1. Ife = 30° and T = 6 kN, determine the magnitude of the resultant force acting on the cyebolt…

Q: 2-9. If the resultant force acting on the support is to be 1200 Ib. directed horizontally to the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: If = 30°, F, = 5 kN, and the resultant force is to be directed along the positive y axis, determine…

Q: Resolve the 30-1b force into components along th: * and waxes and determine the magnitude of each…

Q: *2-96. The tower is held in place by three cables. If the force of each cable acting on the tower is…

A: x = 20 m , y = 15 m Force along DA = 400 N Force along DB = 800 N Force along DC = 600 N

Q: 2-23. Determine the magnitude of force F so that the resultant FR of the three forces is as small as…

A: Apply Parallelogram law FA=82+62=10N θ=tan-186=53.13°

Q: F2-31. Determine the magnitudes of the components of the force F = 56 N acting along and…

A: The point vectors given here are: O0,0,0, A-1.5,3,1, B0,3,1, C0,0,1, D0,0,2 Force 'F' is acting…

Q: If the resultant force acting on the bracket is to be 750 N directed akong the positive A axin,…

A: As per the company's guidelines when multiple questions are asked only first question has to be…

Q: •2-33. If F, = 600 N and = 30°, determine the magnitude of the resultant force acting on the eyebolt…

Q: F2-8. The force F 450 lb acts on the frame. Resolv this force into components acting along members…

A: Given For the given arrangement To determine Resolve the 450 lb force along AC and AB

Q: 2-1. If 0 = 60° and F = 450 N, determine the magnitude of the resultant force and its direction,…

A: given:θ=600Force F=450N

Q: 2-15. The plate is subjected to the two forces at A and B as shown. If 0 = 60°, determine the…

A: Draw the diagram showing the forces and the angles. Apply the equilibrium equation in x- direction.…

Q: 2-25. The log is being towed by two tractors A and B. Determine the magnitude of the two towing…

Q: F2-3. Determine the magnitude of the resultant force and its direction measured counterclockwise…

Q: *2-100. Determine the magnitude and coordinate direction angles of the resultant force acting at…

Q: •2-1. If e = 30° and T = 6 kN, determine the magnitude of the resultant force acting on the eyebolt…

Q: 2-10. Determine the magnitude of the resultant force and its direction, measured counterclockwise…

A: Given data Forces acting are 800lb, 500lb

Q: •2-29. The beam is to be hoisted using two chains If the resultant force is to be 600 N directed…

A: Resultant force, R=600 N (acting in positive y-direction)

Q: 2-62. The 8-m-long cable is anchored to the ground at A. If z=5 m, determine the location +x, +y of…

A: The position vector of A A=xi+yj x=y A=xi+xj B=zk z=5m B=5K The length of the cable is AB=8m

Q: •2-9. The plate is subjected to the two forces at A and B as shown. If e = 60°, determine the…

Q: 2-115. Determine the magnitude of the projection of the force F1 along cable AC. C F = 40 N 4 m F, =…

Q: 2-47. Determine the magnitude and orientation, measured counterclockwise from the positive y axis,…

Q: 2-5. The device is used for surgical replacement of the knee joint. If the force acting along the…

A: Given Data: The force acting along the leg is, F=360 N.

Q: *R2-8. Determine the projection of the force F along the pole. F= {21 + 4j + 10k} kN -2 m

Q: 2-42. Determine the magnitude and orientation, measured counterclockwise from the positive y axis,…

Q: 4 - The horizontal component of the force ( F ) is ( 60 N) to the right through the original point .…

A: Given data: - The horizontal component of the force F is Fh = 60 N.

Q: F2-6. If force F is to have a component along the u axis of F. = 6 kN, determine the magnitude of F…

Q: F2-6. If force F is to have a component along the u axis of F=6 kN, determine the magnitude of F and…

Q: *2-72. Determine the projection of force F = 400 N acting along line AC of the pipe assembly.…

A: Given Data: The value of force acting at C is, F=400 N.

Q: F2-5. The force F = 450 lb acts on the frame. Resolve this force into components acting along…

A: Given data as per question Force F =450 lb Considering force diagram of the system

Question

2-46. The three concurrent forces acting on the screw eye
produce a resultant force Fg 0. If F =F, and F, is to
be 90° from F, as shown, determine the required magnitude
of F3 expressed in terms of F1 and the angle 0.
60
30
F.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

QI. The three concurrent forces acting on the screw eye produce a resultant force F = 0. If F2= 0.8 F, and F, is to be 90° from F, as shown. Determine the required magnitude of F, expressed in terms of F, and the angle 0.
Q3.The force F - 5001b acts on the frame. Resolve this force into component acting along members AB and AC and determine the magnitude of each component.
When F1 = 400 (N), F2 = 500 (N), find the resultant force (R).
If the resultant force of the two tugboats is 3kN, directed along the positive x axis , determine the required magnitude of force Fb and its direction θ.
The force F450 lb acts on the frame. Resolv this force into components acting along members AB an AC and determine the magnitude of each component. 450 lb B F2-5
If the resultant force acting on the support is to be 1200lb directed horizontally to the right determine the force F in the rope A and the corresponding angle
The boat is to be pulled onto the shore using two ropes. If the resultant force is to be 80 KN, directed along the direction of the boat, determine the magnitudes of forces T and P acting in each rope and the angle θ of P so that the magnitude of P is a minimum. T acts at 30o .
The magnitude of the three forces applied to the eye bolt are T1 = 550 N, T2 = 200 N and T3 =750 N. Solve the magnitude of the resultant force and the direction.
Q3: Answer the following ( 1f the resultant force acting on the support is to be 1200 Ib, directed horizontally to the right, determine the force F in rope A and the corresponding angle 6.
The force F=450 lb acts on the frame. Resolve this force into components acting along members AB and AC, and determine the magnitude of cach component.
Determine the resultant force at A.
If the F1 = F2 = 40 KN determine the angle θ with y axis and φ with y axis so that the resultant force is directed along the positive y axis and has a magnitude of FR = 30 kN