2 A voltage e(t) = 100sin 314t is applied to a series circuit consisting of 10ohms resistance, 0.0 inductance and a capacitor of 63.6uF. Calculate a)expression for i(t), b)phase angle between current, c) power factor and active power consumed, d) peak value of the pulsating energy, e diagrams and circuit.

2 A voltage e(t) = 100sin 314t is applied to a series circuit consisting of 10ohms resistance, 0.0 inductance and a capacitor of 63.6uF. Calculate a)expression for i(t), b)phase angle between current, c) power factor and active power consumed, d) peak value of the pulsating energy, e diagrams and circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A RC network supplied with 40V battery is shown in the following figure: a)Find the mathematical expressions for the transient behaviour of vc, ic and vR when the switched is moved to position 1. Plot the curve of vc, ic and vR. And how much time must pass before it can be assumed, for all practical purposes, that ic = 0A and vc = E Volts? Please step-by-step
Consider the Capacitance = 10uF, Vpeak of +13v during the positive half cycle and -7v during the negative half cycle. If we have a charging time of 18ms, calculate the Forward Resistance of the circuit in ohms. Calculate the Vout during the negative half cycle. Calculate the Vout during the positive half cycle. Calculate the Discharging time of the circuit in seconds.
A LRC electric circuit is conected in series has a voltage source of E(t)=20sin(10t) Volts, and a resistance of 20 ohm, and a inductance of 0.05 Henrys and a capacitor of 0.01 Farads, if the current equal to 0, and the initial charge of the capacitor is 2 coulombs, Calculate the charge in the capacitor when t=0 and the current in the circuit when t > 0
A choke coil of resistance 8 ohm and inductance 0.15 H is connected in series with a capacitor of capacitance 125 ?? across a 230-V, 50- Hz supply. Calculate: (a) the inductive reactance, (b) capacitive reactance, (c) impedance, (d) current, (e) voltage across the coil and the capacitor, respectively. (f) phase difference between the current and the supply voltage.
An air-cored choking coil is subjected to an alternating voltage of 100 V. The current taken is 0.1 A and the power factor 0.2 when the frequency is 50 Hz. Find the capacitance which, if placed in parallel with the coil, will cause the main current to be a minimum. What will be the impedance of this parallel combination (a) for currents of frequency 50 (b) for currents of frequency 40?
a. Find the mathematical expressions for the transient behavior of thevoltage vC and the current iC if the capacitor was initially unchargedand the switch is thrown into position 1 at t = 0 s.b. Find the mathematical expressions for the voltage vC and the current iCif the switch is moved to position 2 at t = 8τ.c. Find the mathematical expressions for the voltage vC and the current if theswitch is thrown into position 3 at t =12τ.d. Find the mathematical expressions for the voltage vC and the current if theswitch is thrown into position 1 at t =14τ.e. Find the mathematical expressions for the voltage vC and the current if theswitch is thrown into position 2 at t =17τ.f. Find the mathematical expressions for the voltage vC and the current if theswitch is thrown into position 3 at t =20τ.g. Plot the waveforms obtained in parts (a)–(f)Demonstrate all necessary steps, formulas and calculations properly.
Explore the challenges and benefits of implementing power electronics-based grid solutions like STATCOM (Static Synchronous Compensator) for voltage control and stability.
For the configuration shown in the figure below, determine Zi if Vs = 40 mV, Sense = 0.5 kΩ, and Ii = 20 µA
Consider a PV module with the following external parameters at STC: Pmax = 320 W, VOC = 45 V, ISC = 8 A, NOCT =40 °C and the temperature coefficient of power is −1 W/°C. a) If the ambient temperature rises to 35 °C while the irradiance is 1,000 W/m2, what is the cell leveltemperature, calculated with the NOCT model?b) What is the new power output of the PV module under the new ambient temperature of 35 °C and 1,000W/m2irradiance?
A RL network supplied with 10V battery (a)Find the mathematical expressions for the transient behaviour of vL, iL , vR2 and vR2 when the switched is moved to position 2. Sketch the curves of vL, iL and vR2.A how much time must pass before it can be assumed, for all practical purposes, that iL=0A and vL = 0 Volt?
Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor with internal resistance of 0.34 ohm and reactance of 47.15 ohms; and a capacitor with reactance of 7.53 ohms. Compute for the magnitude of its equivalent impedance in ohms. Do not round off during computation. final ans 4 decimal places
answer the following questions in reference to the circuit diagram: discharge phase begins when switch is moved from position 1 to position 2 at t = 250 microseconds. find the discharging phase time constant, how long will it take to reach steady state, and find the values of i, vL and vR2 at t = 250+ microseconds