2) Determine the critical axial buckling load for an 8 % x 12 in glu-laminated column braced at 10 ft from the bottom in the y axis for a total height of 25 ft Assume pin connections at top and bottom. Fc3D1750 psi, E=1.8 x 10° psi (Western cross section glu-lam data is in the text.) 3) What is the load to cause the column of problem 2) to crush? Will the column buckle or crush first?

2) Determine the critical axial buckling load for an 8 % x 12 in glu-laminated column braced at 10 ft from the bottom in the y axis for a total height of 25 ft Assume pin connections at top and bottom. Fc3D1750 psi, E=1.8 x 10° psi (Western cross section glu-lam data is in the text.) 3) What is the load to cause the column of problem 2) to crush? Will the column buckle or crush first?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.11P: Determine the critical load Pcrand the equation of the buckled shape for an ideal column with ends...

See similar textbooks

Similar questions

An idealized column is made up of rigid segments ABC and CD that are joined by an elastic connection at C with rotational stiffness ßR= 100 kip-in./rad. The column has a roller support at B and a sliding support at D. Calculate the critical load Pcrof the column.
Rigid column ABCD has an elastic support at B with translational stiffness ß. Find an expression for the critical load Pcrof the column.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
The figure shows an idealized structure consisting of two rigid bars joined by an elastic connection with rotational stiffness ßR. Determine the critical load PCTfor the structure.
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
A square aluminum bar with pinned ends carries a load P = 25 kips acting at distance e = 2,0 in. from the center (sec figure). The bar has a length E = 54 in. and modulus of elasticity E = 10,600 ksi. If the stress in the bar is not to exceed 6 ksi, what is the minimum permissible width bminof the bar?
A pinned-and column of a length L = 2A m is constructed of steel pipe (E = 210GPa) having an inside diameter d1= 60 mm and outside diameter d2= 68 mm (sec figure). A compressive load p = 10 kN acts with eccentricity e = 30 mm. What is the maximum compressive stress max in the column? If the allowable stress in the steel is 50 MPa, what is the maximum permissible length Lmaxof the column?
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
An aluminum pipe column (E = 10,400 ksi) with a length L = 10.0 ft has inside and outside diameters d1= 5.0 in. and d2= 6.0 in., respectively (sec figure). The column is supported only at the ends and may buckle in any direction. Calculate the critical load Pcrfor the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
AW310 × 74 wide-flange steel column with length L = 3.8 m is fixed at the base and free at the top (see figure). The load P acting on the column is intended to be centrally applied, but because of unavoidable discrepancies in construction, an eccentricity ratio of 0.25 is specified. Also, the following data are supplied: E = 200 GPa, y = 290 MPa, and P = 310 kN. What is the maximum compressive stress max in the column? What is the factor of safety n with respect to yielding of the steel?
Determine the critical load Pcrand the equation of the buckled shape for an ideal column with ends fixed against rotation (see figure) by solving the differential equation of the deflection curve. (See also Fig. 11-18.)