2 m Probs. 3-24/25

Q: Determine the value of P just sufficient to start the 10" wedge under the 40-kN block. The angle of…

A: Given: The angle of friction is 20o. Consider the figure,

Q: a b с1 d c2 b

A:

Q: • Cross section of Column:425 mm x 525 mm • Ultimate axial load on column • Ultimate moment along…

A: Solution for Question 1 A is as follows: Given Data: Ultimate axial load on column is P=2500 kN.…

Q: 150 mm 150 mm 150 mm 150 mm 650 mm As = 4 - 32 mm 75 mm

A:

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1-A2= 900 mm? , E1=E2= 100 GPa , a1-a2=…

A:

Q: A compound disk and drum are being acted upon by a force 100lbs which stays horizontal. Assume that…

A:

Q: The force of magnitude F acts along the edge of the triangular plate. Determine the moment of F…

A:

Q: If DA = 17cm, DB = 12cm and L = 4m, and if oil is flowing at a rate of 0.08 m³/ s, determine the…

A: Solution:-

Q: Water Flow into horizontal pipe with velocity of v. Determine the horizontal and vertical component…

A: We will take value of v1 = 3 m /s D1 = 0.6 m D2 = 1.5 m

Q: Calculate the minimum force P required to keep the 0.294 KN rod AB from sliding. The contact surface…

A:

Q: Replace the force system by an equivalent resultant force couple moment at point O. Take and F3 =…

A:

Q: Problem Set - 2: The simply supported steel beam is loaded by the 20 kN-m couple as shown in the…

A:

Q: The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of…

A:

Q: 4. A solid cylinder of diameter 4.5 has a height of 2.5 metres. Find the meta-centric height of the…

A:

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

A: Since the truss is symmetrical about y-axis , there will not be any horizontal displacement of point…

Q: W MB B k 4 m 2 m The cantilever beam above is made up of concrete with E = 70 MPa, refer to the…

A: Given  Required : Slope at B

Q: Compute the nominal axial load capacity (KN) of the column that can be applied at an eccentricity of…

A: The given data is: L=600 mm B=300 mm e=250 mm Assuming that section is M 20 with fe=415

Q: 200 A 400

A: For an object , while drawing free body diagram the weight , frictional force (if surface is rough)…

Q: Q3: A tank containing water upto a depth of 500 mm is moving vertically upward with a constant…

A: GivenDepth, h=500mm=0.5mAcceleration, a=2.45 ms2    same for both directionWidth=2m

Q: Determine the smallest horizontal force P required to lift the 1 00-kg cylinder. The coefficients of…

A:

Q: Q5/ If the magnitude of the resultant force is to be 9 kN directed along the positive x-axis,…

A:

Q: Question 7: Analyse the portal frame shown below and draw the BM, SF and axial force (AF) diagrams,…

A:

Q: 3. Determine the velocity of the 75-lb block A if the two blocks are released from rest and the…

A: Given  Kinetic friction coefficient = 0.10

Q: a feed at A to a ramp at B by a rotating rod. If the rod rotates angular velocity of 0=0.5 rad/s and…

A: Mass m=3kg angular velocity r= 1.2cosθ θ=0.5rad/s In order to calculate the forces which the rod…

Q: 3k/ft De -8 ft- - 20 ft- 8 ft-

A:

Q: The 49-kg block rests on the horizontal surface, and a force P = 427 N, whose direction can be…

A: F=μsNEquilibrium about  y-direction∑ Fy=0-Psinθ+N-mg=0N=499.81+427sin39N=749.41 NEquilibrium about…

Q: The crankshaft is subjected to a torque of M = 50 N ⋅ m. Determine the horizontal compressive force…

A: Given: The torque is M = 50 N-m. The angle is θ = 60°. Consider the figure.

Q: Compute the moment of inertia for the built up section shown below about the strong axis only.…

A:

Q: A carport roof is supported as shown in Figure P6-10. If the roof has a mass of 200 kg, determine…

A: The weight of the mass (200 Kg) = 200×9.81 = 1962 N The Location of weight of the roof will be at…

Q: (a) Draw the FBD of A and B when the wedge B impends to slide to the left. Friction is negligible…

A:

Q: Find the moment of inertia about centroidal axis in X direction of rectangular section having width…

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

A:

Q: Que : A hollow circular shaft of Inner Radius 6 cm and Outer Radius 10 cm and length 200 cm is…

A: Given data, Length of the shaft=L = 200cm  Angle of twist at free end= 0.01rad   Maximum shear…

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

A:

Q: A 400 mm x 500 mm rectangular tied column is reinforced with eight (8) D28mm longitudinal bars, four…

A: The given data is shown below:

Q: A cylindrical tank is at rest as shown. The tank has a weight of 100 kN. Ap- proximately what…

A: From fig:x2=82-42x=43

Q: Determine FEMAB of the beam with uniform varying load of 23 kN/m, 1 meter from the left fixed…

A:

Q: Determine the Maximum shown Where: P = 85kN; w = 10kN/m; L1 = 4m; L2 = 10 P

A:

Q: 18 kN/m 4 m 9 kN/m 4 m Probs. 14-109/110 . Determine the slope at A of the A-36 steel W200 x 46…

A: Given, There is A simply supported beam Of span 8 m loaded with Udl  . There are two Different…

Q: Determine the distance s to which the 90-kg painter can climb without causing the 4-m ladder to slip…

A:

Q: Determine the distance s to which the 90-kg painter can climb without causing the 4-m ladder to slip…

A:

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm2 , E1=E2= 100 GPa, a1-a2=…

A: Given Data: The area of member AB and CB is, A1=A2=900 mm2 The elastic modulus of both members is,…

Q: Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70 x 10^6 mm^4.…

A: A loaded beam is given and it has been asked to determine slope and deflection at c using moment…

Q: Determine the slope (rad) at point B of the beam shown below. 90 kN B 5 m El = constant E = 200 GPa…

A: A beam 5 metre long fixed at one end and free at another ( cantilever) having load of 90kN at free…

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

A:

Q: The ratio of the torsional moments of resistance of a solid circular shaft of diameter D, and a…

A: For detailed solution, see the step 2

Q: Neglect friction of the 55-Ibf collar against its vertical guide and compute the velocity of the…

A:

Q: -10ft- 60kip E = 29,000ksi I= 4,000 inª 10ft-

A:

Q: Compute the axial force of column AB. * O a. 122.90 kN-m O b. 132.75 kN-m O c. 144.18 kN-m O d.…

A: First draw the FBD of whole structure and calculate the reaction at C by summing up moments at point…

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.