2) The member AB is supported by a cable BC and at A by a square rod which fits loosely through the square hole at the end joint of the member as shown. It supports the cylinder load of magnitude 800 lb. Determine the safe diameter of cable BC if the stress is limited to 110 MPa. 2 ft B 3t

2) The member AB is supported by a cable BC and at A by a square rod which fits loosely through the square hole at the end joint of the member as shown. It supports the cylinder load of magnitude 800 lb. Determine the safe diameter of cable BC if the stress is limited to 110 MPa. 2 ft B 3t

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: (O 5 day BOD of wastewater and Gil ultimate BOD. Assume K = 0.12/day. %3D

A: BOD 5 IS TO BE CALCULATED

Q: Determine the elongation (+) or shortening (-) between points BC, of the bar made of A36 structural ...

Q: Water flows in a 4-cm-diameter pipe at 18 m/s. The pipe enlarges to a diameter of 6 cm. Calculate th...

Q: QUESTION 3 The two alternative dpeths in a 4.0 m wide rectangular channel are 3.86 m and 1.0 m, resp...

Q: Determine the maximum deflection for the beam shown by the moment-area method. 80 kN C В 12 m 12 m 2...

A: Given data: E = constant = 200 GPa I=600(106)mm4

Q: Consider shaft AB that is fixed at point A and free at point B that is subjected to the torque T. Th...

Q: 8: A wastewater sample was diluted 10% with tap water for conducting BOD Test. The DO content in was...

Q: Q.46 A Nozzle of diameter 20 mm is fitted to a pipe of diameter 10 min find the force exerted on the...

A: P1 + ρgh1 + ρu122=P2 + ρgh2 + ρu222 Since we have same elevation So, ρgh1 = ρgh2 So, gets cancelle...

Q: 2. The vertical steel bars BE and CF supports the horizontal rigid bar ABCD and the applied forces a...

A: Modulus of elasticity of steel (E)=200GPa To find displacement at A and D

Q: SKETCH THE FIGURE AND SHOW THE COMPLETE SOLUTIONS

A: Step: 1 Latitude and departure are the projection of a line in north-south and east-west direction ...

Q: Determine the value of load P if At = 30 °C and the stress in bronze is limited to 132 MPa. Aluminum...

Q: 40 kN 20 kN/m 10 kN/m 3m 3m 4m 10m 4m 6m Hinge -Hinge R1 R2 R3 R4

Q: Given: Open water source Net radiation = 200 W/m? Air temperature = 25 °C Density of water = 997 kg/...

Q: and Draw the V diagram Write the shear and moment equations (not simplified and simplified) at each ...

Q: ment and was designed with a 8-inch slab, 90% reliability, 700 lb/in2 concrete modulus of rupture, 5...

Q: The tube shown in Fig. 2-7 is filled with oil. Determine the pressure heads at A and B in meters of ...

A: Consider the figure,

Q: sand 2.60 and gravel is 2.70. Determine the volume of sand in m3 to be mixed with 1 bag of cement:

Q: A local camera station is tracking a UFO sighting in the evening sky, Find the velocity and accelera...

Q: SITUATION: The beam carries a moment of 60kN/m. Use fc = 9MPA, fs = 124 MPa, n = 10. Determine the s...

Q: 1. Determine the following parameters for the design of concrete beam reinforced for tension only. T...

Q: which type of urban road would have free-flow traffic characteristics? 1. Arterial 2. Local 3. Freew...

A: (3) is the correct answer. Freeway have the maximum free flow speed. Where the speed, density and vo...

Q: Water enters the lock of a ship canal through 200 ports, each port having a 2 ft x 2 ft cross-sectio...

Q: 16. While calculating the handling capacity of lift, the weight of a person is taken as 65kg. A. O T...

Q: A soil has liquid limit of 60% plastic limit of 35% and shrinkage limit of 20% and it has a natural ...

Q: 4. A reinforced concrete beam having a width of 250 mm, effective depth of 350 mm, and d' = 65 mm is...

Q: The testing of concrete for compression will require the preparation of 12 standard concrete cylinde...

A: Given data, Diameter of concrete d = 150 mm Height of concrete h = 300 mm Mix proportion = 1:2:4 Sp...

Q: h

Q: You are hired by a developer to calculate the total forces on the bottom of the side of a dam where ...

Q: 13. A3 m wide rectangular channel conveys 12 m/s of water at a depth of 2 m. Calculate: (1) Specific...

A: Given, Width of channel (b) = 3m Normal depth = y= 2m Discharge (Q)=12 m³ /sec q= Q/b= 12/3 = 4m²/s...

Q: The magnitude of fixed end moment developed at support A is. kNm. 12 kN/m -12 m-

A: We use theorem of least work to find redundant

Q: Describe what is meant by the phrase “field-to-finish.”

A: The surveying procedure that determines the connectivity and symbology of points surveyed in the fie...

Q: Determine 6, and 8, at point Busing double integration method. El is constant. B 3 17 17

Q: For the truss shown and loading, determine the axial stress in member BG in ksi. Use two decimal pla...

Q: 20. At roof slab level over the DPC, are provided. A. O Tiles B. O Concrete С. О Р.С.С D. O Rubber S...

A: Answer- Tiles Explanation -Tiles are provided at roof slab level over the DPC to reduce the dampness...

Q: . A reinforced concrete T Beam has a width of 800 mm and a thickness of 50 mm. It has an effective d...

Q: 1. A hollow steel column is subjected to a load of 180-KN, determine the change in length if the mod...

Q: 14. A fire detector cannot detect: А. Radiation В. О Неat C. O Light D. O Smoke

Q: For the rectangular lot, observations of sides A and Bwith their 95% errors are (252.46, {0.053) and...

A: Given:- The observations of sides A and B with 95% errors are:- A = (252.46 ± 0.053) ft B = (605.08 ...

Q: A 3.5m high column consists of W920 X 289.7. It carries an eccentric load of 1000 KN with an eccentr...

A: Given, Load=100 kNFY=248 MPaLength=3.5 mmArea A=36770 mm2d=927 mmbf=308 mm tf =32 mm tw=19.4 mm Ix=5...

Q: In a reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of...

Q: Explain and show the step-by-step procedure for differential leveling and Discuss other relevant inf...

A: For the sake of summarising, the following is the technique for differential levelling: 1. Prepare t...

Q: In the figure as shown, determine the following: What is the change in length of the bar? What shoul...

Q: A large tank open to the atmosphere is filled with water to a height of 5 m from the outlet tap. A t...

Q: Assuming k = 3000 lb/in², and considering only the bending stress: What rail type would you recommen...

A: Given, Track modulus (k) = 3000 psi Force (P) = 30000 lb

Q: rectangular beam carrying a uniform load of 26 KN/m, including its own weight, is limited in cross ...

Q: Write the shear and moment equations (not simplified and simplified) at each segment of the beam sho...

Q: Explain and show the step-by-step procedure for differential leveling and Discuss other relevant inf...

A: The most common approach for getting the ground points elevation relative to a reference datum is le...

Q: Initial weight: % Passing Weight Retained 1.5 kg 1.634 kg 2.5 kg 1.8 kg 2.273 kg 0.233 kg 0.06 kg Si...

Q: Suppose a free-fall ride at an amusement park starts at rest and is in free fall. What is the veloci...

A: Given data- Initial velocity u=0 m/sfree fall condition, hence acceleration-a=g=9.81 m/s2Time t=2.3 ...

Q: he following are the properties of a steel section to be used for a column element that is pinned at...

A: Step 1: Euler’s allowable axial stress r = √ 9.9 x10^ 7/21300 =68.175mm k=0.7 σ = π2 x 2 x10^5 / ((0...

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

Subject: strength of materials

Hi, please provide clear solutions thank you

Box final answers and round off to nearest two decimal places

2) The member AB is supported by a cable BC and at A by a square rod which fits
loosely through the square hole at the end joint of the member as shown. It
supports the cylinder load of magnitude 800 lb. Determine the safe diameter
of cable BC if the stress is limited to 110 MPa.
2 ft
B
3ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A load W is to be lifted using the crane which is hinged at B as shown in the figure. The value of x1 is 10m, x2 is 8m and h is 18m. Neglecting the weight of the crane. Determine the following. 1. Force at cable AC. 2. Resultant reaction at B. 3. Largest load that can be lifted if the maximum force of cable AC is 50kN.
ENGINEERING MECHANICS (No lng explanation needed. Write the complet solutions and legibly. Rate will be given) Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation speed of 300 rpm where the diameter of the shaft AB and CE are 10 mm and 15 mm, respectively The allowable shearing stress is 1 GPa with F.S. of 1.2 for both shafts. Neglect the deformation of the cable at E. Where: Radius of the gear at B, rB = 100mm Radius of the gear at C, rC = 150mm
The section of the masonry dam is as shown. The specific weight of water is 9.81 kN/m^3 and that concrete is 23.54 kN/m3. Determine the following: a. The resisting moment b. The factor of safety against overturning c. The factor against sliding if the coefficient of friction is 0.60
Determine the stress of 5-mm radius cable CD that supports the bar AB at 150-kilograms and a 2,000 kg/m² force at point A. Hint: W=m*g
The rectangular beam ABC, 133 mm wide by 322 mm deep, is supported by a pin at A and the cable CD. Determine the normal stress (in MPa) at the bottom of the beam and at asectionofthebeam 1.07 m from the pin if P = 499.99 kN.
6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.
A crane boom of mass 450 kg with its centerof mass at C is stabilized by two cables AQ and BQ(Ae = 304 mm2 for each cable) as shown in the figure.A load P 5 20 kN is supported at point D. The craneboom lies in the y-z plane.(a) Find the tension forces in each cable: TAQ and TBQ(kN). Neglect the mass of the cables, but includethe mass of the boom in addition to load P.(b) Find the average stress (σ) in each cable.
The boom DF of the crane and the column DE have a uniform weight of 40 lb/ ft. A load of 300 lb is applied at hoist attached to F. Determine the resultant internal loadings in the crane on cross-sections through points A, B, and C.
The boom AB lies in the vertical y-z plane and is supported by a ball-and-socket joint at B and by the two cables at A. A 20-kN force acting in the horizontal plane and applied at the midpoint M of the boom. Neglect the weight of the boom. 70. Calculate the tension T1. Calculate the tension T2.
Three loads are suspended as shown from the cable ABCDE. Knowing that dc = 3 m, determine the sag at DB
The system is released from rest with the cable taut. The mass of blocks A and B are 54 kg and 25 kg, respectively. For the friction coefficients ?s = 0.25 and ?s = 0.2, calculate the tension in the cable in Newton. Neglect the small mass and friction of the pulleys. Use g = 9.81 m/s2
A light bar AB supports a 15-kg block at its midpoint C. Rollers at A and B rest against frictionless surfaces, and a horizontal cable AD is attached at A. Determine the tension in cable AD.