2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the cylinder is carrying a load of 25 KN. FInd the stress in cylinder , also find deformation of the cylinder E=100 Gpa.
Q: In the test on a steel bar, E = 29.57 x 10° psi and v = 0.303. Find the shear modulus, G. %3D
A: Given data: E=29.57×106 psiν=0.303 Need to determine the value of shear modulus.
Q: A mild steel rod of 25 mm diameter and 400 m long is encased centrally inside a hollow copper tube…
A: Axial deflection of arbitrary cross-sectional bar of elastic material having length L is given by…
Q: A steel bar of cross-sectional area 200 mm^2 is loaded as shown in Fig. Find the change in length of…
A: For solution refer below images.
Q: A steel bar with length of 4.5 m is subjected to forces as shown in the figure: 1. Determine the…
A:
Q: The 4 mm diameter cable BC is made of a steel with E = 200 GPa. If it is known that the maximum…
A:
Q: the bar shown is subjected to uniform tensile stresses along the x and y axes of a magnitude 676…
A: Given Data Stress in x direction, 676MPa Stress in y-direction, 676 MPa Modulus of elasticity,…
Q: 90 kN Find the total deformation for the bar shown in fig. if the axial loads are applied if cross…
A: To find : The total deformation of the bar . Given data : Cross section area of each section (A)=450…
Q: The bar shown in Fig. is subjected to a tensile load of 50 kN. Find the diameter of the middle…
A:
Q: A solid steel post having a length of 3m and a diameter of 80 mm is subjected to pure torsion. a)…
A: Answer: (a) The torsional rigidity of the steel post is 321.7 × 109 N•mm2. (b) The torsional…
Q: Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is…
A:
Q: Find out the crippling stress of the column if E=2×105N/mm2 . Also, find out the shortest length of…
A: Given: Fix-hinge support do=40 mm=0.04 mdi=20 mm=0.02 mL=5 mE=2×105 N/mm2σy=250 N/mm2 To determine:…
Q: A square tie bar 20 mm x 20 mm in section carries a load. It is attached to a bracket by means of 6…
A:
Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kNm show in…
A: Given:P=400 kNσ=120 MPainside diameter= 100 mm
Q: Two steel wires support a movable overhead camera weighing W=25lb (see figure) used for close-up…
A: Data given-
Q: A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4 m. A bore of diameter…
A: Given: Tensile load P=40 KN Diameter of the rod D=40 mm Area of the road A=π4D2…
Q: 2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the…
A:
Q: A circular bar having 300 mm2 area is subjected to axial loads as shown in f value of (P) and the…
A: given:cross section area of the bar A=300mm2E=2×105N/mm2
Q: A 4-mm-diameter steel wire, 3.2 m long, carries an axial tensile load P. Find the maximum safe value…
A:
Q: 4. A wood post 12 in. by 12 in. is braced by four steel angles. The wood post and the pieces of…
A: As per the bartleby policy we can solve only three subparts of any question. Given Data The length…
Q: 3. Bars AB, CD, and EF each have a cross-sectional area of 25 mm and modulus of elasticity E= 200…
A:
Q: 3. A mild steel rod supports a tensile load of 50 kN. If the stress in the rod is limited to 100…
A: Given Data: Tensile load, P=50 kN Stress, σ=100 MPa
Q: A solid steel post having a length of 3m and a diameter of 80 mm is subjected to pure torsion. a.…
A:
Q: An iron column of annular cross-section has an outer diameter of 200 mm and is subjected to a force…
A: Given Data⇒Iron column of annular cross-sectionOuter diameterD=200 mm=0.2 mForceF=75 KN=75×103…
Q: Determine the total deformation of the steel rod shown in figure under the given loads. Take the…
A:
Q: For the steel block (Length L = 5-meter, Width W = 1 meter, Height H = 1 meter) with compression…
A:
Q: Q.1 A 2 m solid steel bar of diameter 100 mm is subjected to a axial tensile load of 100 kN. Find…
A: Given: The diameter of the shaft is, d=100 mm. The length of the steel shaft is, l=2 m. The value…
Q: A 150 inch long aluminum bar is subjected to a tensile stress of 25000 psi. Find the elongation. (E…
A:
Q: 4. A steel bar of 40 mm x 40 mm square cross-section is subjected to an axial compressive load of…
A: Given, Cross sectional area = A = 40 mm x 40 mm = 1600 mm2 Axial compressive load = P = 200 kN = 200…
Q: A hollow cylinder 2 m long has an outside diameter of 50 mm and inside diameter of 30 mm. If the…
A: According to Hooke's Law, Stress is directly proportional to the strain up to a certain point. After…
Q: block P 5 kN b. 5 kN. rigid plate 2x10 mm 2x10 mm
A:
Q: he beam supports an 80 kg vertical mass applied at D. The beam is pinned to the wall at point A and…
A: Here, BC=15cm×15cm E=70GPa Load at D, FD=80×g=80×9.81N=784.8N Taking moment about point A. ∑MA=0…
Q: aw the free body diagram of the system shown below b.) Formulate the different equations of stress…
A: To determine the total elongation in the bar.
Q: Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a…
A:
Q: Figure Q4 (a) shows an L-bracket ABC which lies in the horizontal plane. It is made from a material…
A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…
Q: The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the…
A: Given: The structure is made up of stock (same stock for A-B-C and B-D). 5 mm thick. b mm wide.…
Q: 3. Bars AB, CD, and EF cach have a cross-sectional area of 25 mm and modulus of clasticity E=200…
A:
Q: Question 2 A rod, which tapers uniformly from 40 mm diameter to 20 mm diameter in a length of 400 mm…
A:
Q: A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid…
A:
Q: A steel rod having a cross-sectional area of 300 mm2 and a length of 150 m is suspended vertically…
A:
Q: Strains measured in a, b and c directions are yardımıa=-150x10-6, ɛb=200x10-6, and ɛc=300x10-6 with…
A: Given Data ɛa =-150x10-6 ɛb =200x10-6 ɛc =300x10-6 E=200 GPa Poisson ratio ν= 0.3
Q: Problem 2) As a result of loading, the rectangle with a = 25 mm and b = 18 mm deforms into a paral-…
A:
Q: A steel bar with length of 4.5 m is subjected to forces as shown in the figure: 1. Determine the…
A:
Q: In the figure, member AB is used to support a load of 20kN at the free end, if the cable CD has a…
A: Answer: tensile stress in the cable = 62.37 MPaFor a step-by-step solution have a look through the…
Q: (3): A steel bar ABCD (4m) long is subjected to forees as shown in Figure. Find the stresses in each…
A: given:
Q: Q1// A hollow shaft of 10mm inside diameter and 5mm thick and 2m long extends by 0.5 cm under a…
A: Write the given values along with the suitable variables.
Q: 5 in. 8 in. A Two bars are used to support a load P. When unloaded, AB is 5 in. Iong, AC is 8 in.…
A:
Q: A pick-up truck tailgate supports a crate where Wc= 150 lb. as shown in the figure. The tailgate…
A: Given, WT=60 lbWC=150 lbAc=0.017 in2dT=14 indc=18 inL=16 inH=12 in The angle and length of the…
Q: Q2- The homogeneous bar AB have diameters ubjected to an axial tensile load of 25KN. have he new…
A: SOM Note: Working stress should be 0.25 N/mm2
Q: 10 cm 600 N 14 cm B -- Vertical load is applied to point Bof a 10 mm radius cylindrical bar as shown…
A: Given data: Radius of the cylindrical bar is: r=10 mm which is fixed at point 'C'. We need to find…
Q: The uniform 300-1b bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B…
A:
Step by step
Solved in 2 steps with 2 images
- A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
- A symmetrical framework consisting of three pin-connected bars is loaded by a force P (see figure). The angle between the inclined bars and the horizontal is a = 52°. The axial strain in the middle bar is measured as 0.036. Determine the tensile stress in the outer bars if they are constructed of a copper alloy having the following stress-strain relationship:Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPaA cast-iron plate in biaxial stress is subjected to tensile stresses x= 31 MPa and y. = 17 MPa (see figure). The corresponding strains in the plate are x=240106 and y=85106 . Determine Poisson’s ratio v and the modulus of elasticity C for the material.
- A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a tensile force P (see figure). If the bar elongates by 0.0)95 in., what is the decrease in diameterA brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
- A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?