Solve the sub-part (A) only,only typing 2. A single phase full wave ac voltage controller supplies an RL load. The input supplyvoltage is 230V, RMS at 50Hz. The load has L= 10mH, R = 1052, the delay angle ofSCR 1 and 2 are equal, where al=a2=/3, B=197.4°Determine :a. Conduction angle of the thyristor.b. RMS output voltage.c. The input power factor.

2. A single phase full wave ac voltage controller supplies an RL load. The input supply voltage is 230V, RMS at 50Hz. The load has L= 10mH, R = 1002, the delay angle of SCR 1 and 2 are equal, where al=a2=n/3, B=197.4° Determine: a. Conduction angle of the thyristor. b. RMS output voltage. c. The input power factor.

2. A single phase full wave ac voltage controller supplies an RL load. The input supply voltage is 230V, RMS at 50Hz. The load has L= 10mH, R = 1002, the delay angle of SCR 1 and 2 are equal, where al=a2=n/3, B=197.4° Determine: a. Conduction angle of the thyristor. b. RMS output voltage. c. The input power factor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A TRIAC phase control circuit has a load resistance of 60 and is powered by an AC source of 188 VRMS. With symmetrical switching, determine the load RMS voltage in Volts. Assume α = 98 degrees. Express your answer in three decimal places.
An audio power amplifier delivers an 80-volt peak 35 Hz sine to a subwoofer. If the subwoofer impedance at this frequency is 4 at −30°, determine the peak current delivered to the load and the true power.
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
A 4-quadrant DC chopper with bipolar switching operating at a switching frequency of 2kHz, is connected to a 120VDC source (Vs) and a DC motor which has a counter EMF (CEMF) of 50VDC at rated speed. The armature resistance is 2Ω and the armature inductance is 20mH. Calculate: a) Output voltage with an 80% duty cycle b) Magnitude and direction of the DC armature current with an 80% duty cycle. c) Duty cycle for a forward braking current of 10ADC. (Assume the speed has not changed due to the large inertia of the load.)
Could you please go more in depth about how to create the ac equivalant model? thank you
Define ICBO and ICEO. How are they different? How are they related? Are they typically close in magnitude?
Consider the AC circuit shown in the image, that is driven by a voltage V=V0cos(ωt). a) What is the current through the capacitor, C? Give its amplitude and phase relative to the drive voltage. b) What is the total current through the voltage source? Again require amplitude and phase relative to the drive voltage.
11. Why is the conduction angle greater with an inductive load than with a purely resistive load? 12. For a full-wave phase control circuit draw the output voltage and current waveforms when firing angle α = (45-X)° (Here X= 10). Consider the load to be inductive. 13. What point in a single-phase ac waveform is used as a reference point for timing the thyristor gate pulses?
1- Derive expression for the output rms voltage for single phase ac voltage controller with resistive load
The TRIAC based AC voltage controller operates in phase control mode. The regulator is used to control heat of a welding coil. The supply voltage is 230V, 50Hz and heating element has a resistance of 20Ω. If the TRIAC is fired at an angle of 500 , compute the rms value of the output voltage, rms value of the output current and power delivered to the load.
find dc and ac analysis
6/ (a) Describe the basic Microwave transmission system and give the importance of each component in the system. (b) What are Microwaves? Bring out the basic advantage of Microwaves over Co-axial cables and the Fiber optics.