2. A single plate clutch with both sides of the plate effective is required to transmit( 25 kW) at (1600 r.p.m). The outer diameter of the plate is limited to (300 mm) and the intensity of pressure between the plates not to exceed (0.07 N/mm². Assuming uniform wear and coefficient of friction 0.3, find the inner diameter of the plates and the axial force necessary to engage the [Ans. 90 mm; 2375 NJ clutch.

2. A single plate clutch with both sides of the plate effective is required to transmit( 25 kW) at (1600 r.p.m). The outer diameter of the plate is limited to (300 mm) and the intensity of pressure between the plates not to exceed (0.07 N/mm². Assuming uniform wear and coefficient of friction 0.3, find the inner diameter of the plates and the axial force necessary to engage the [Ans. 90 mm; 2375 NJ clutch.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.76P: The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force...

See similar textbooks

Similar questions

Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 3.3kN. The inside radius of the contact surface is 81mm and the outside radius is 110 mm. Assume uniform wear.
the power transmitted by a single plate clutch at a speed of 2000 rpm, if the outer and inner radii of Triction surfaces -are 150 mm and 100 mm respectively. The maximum intensity of pressure at any point of contact surface should-not exceed 0.8 x 105 N/m2. Take both sides of the plate as effective and coefficient of friction = 0.3. Assume uniCalculateform wear.
Determine the size of the clutch plate suitable for an Ambassador car employing asingle plate type friction clutch and developing 37.5 kW at 4282 rpm. The insidediameter of the clutch plate is 0.6 times its outside diameter and it is to be ensured thateven after a loss of 30% of the engine torque due to wear of the clutch facing, the clutchdoesn’t slip. The intensity of the pressure on the facing is not to exceed 70 kPa. Assumeµ = 0.3.
A local utility vehicle production company have considered using in one of its design a multi-disc clutch consisting of a 9 steel disc and 8-bronze discs with effective outside and inside diameter of 220mm and 160mm, respectively. If the shaft turns at 150rpm and an axial force of 600N is applied, find the horsepower capacity, considering a coefficient of friction of 0.25
Two identical ball bearings Pand Qare operating at loads 30 kN and 45 kN respectively The ratio of the life of bearing P to the life of bearing Q is....
A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the systemhas a diameter 150 mm and rotates at 200 rev/min. The grove angle is 40° and thecoefficient of friction between the belt and pulley is 0·3.(a) If the maximum tension in any one belt is limited to 800 N and the angle of lap is135°, determine the number of belts required. (b) Determine also, the initial pre-tension required in the belt.
A band brake is installed on a drum rotating at 250 rpm, and a diameter of 900 mm. The angle of contact is 1.5 pi radians and one end of the brake band is fastened to a fixed pin while the other end of the brake arm is 150 mm from the fixed pin. The coefficient of friction is 0.25 and the straight brake arm is 1000 mm long and is placed perpendicular to the diameter bisecting the angle of contact. Determine the net band pull in kN applied at the end of the brake arm if 50 kW is being absorbed.
An engine of a motor vehicle with a wheel diameter of 712 mm develops 50 kW at 2,000 rpm combined efficiencyof the differential and transmission is 75% with an over-all speed reduction to. 1 determine he torque to bedelivered by the clutch N-m.
A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficient of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
A centrifugal clutch is to be designed to transmit 15 kW at 900 r.p.m. The shoes are four in number. The speed at which the engagement begins is 3/4th of the running speed. The inside radius of the pulley rim is 150 mm. The coefficient of friction may be taken as 0.25. Determine: 1. mass of the shoes, and 2. size of the shoes.
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition