2. An engine developing 45 kW at 1000 rpm is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 12.5° and a maximum mean diameter of 500 mm. The coefficient of friction is 0.2. The normal pressure on the clutch face is not to exceed 0.1 N/mm2. Determine: a. the face width required, and b. the axial spring force necessary to engage the clutch.

2. An engine developing 45 kW at 1000 rpm is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 12.5° and a maximum mean diameter of 500 mm. The coefficient of friction is 0.2. The normal pressure on the clutch face is not to exceed 0.1 N/mm2. Determine: a. the face width required, and b. the axial spring force necessary to engage the clutch.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.56P: The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The...

See similar textbooks

Similar questions

The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
A cone clutch with a cone angle of 12° transmits 53 kW at 1300 rpm. The coefficient of friction of linings is 0.16. Determine the axial spring force necessary to engage the clutch in N if the mean diameter of the active conical sections is 250 mm.
A centrifugal clutch is to be designed to transmit 15 kW at 900 r.p.m. The shoes are four in number. The speed at which the engagement begins is 3/4th of the running speed. The inside radius of the pulley rim is 150 mm. The coefficient of friction may be taken as 0.25. Determine: 1. mass of the shoes, and 2. size of the shoes.
Determine the axial spring force necessary to engage the clutch, when an engine developing 30kW at 500 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 13.5o and a maximum mean diameter of 300 mm. The coefficient of friction is 0.25. The normal pressure on the clutch face is not to exceed 0.1 N/mm2
A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the mean diameter is to be 355mm. The coefficient of friction between the contacting surfaces is 0.20 and the maximum normal pressure is 83 kPa, determine the outside diameter of the clutch. a. 384.3 mm b. 356.2 mm c. 349.5 mm d. 339.2 mm
An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two square-thread lead screws, 1.5 inches in (major) diameter, are used for this application. Determine the torque required to raise this lift if the moving part of the elevator weighs 800 pounds and the coefficient of friction is assumed to be 0.15. For the elevator described, find the efficiency and power required if each lead screw is driven at 175 rpm. Verify if this is self locking.
A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the systemhas a diameter 150 mm and rotates at 200 rev/min. The grove angle is 40° and thecoefficient of friction between the belt and pulley is 0·3.(a) If the maximum tension in any one belt is limited to 800 N and the angle of lap is135°, determine the number of belts required. (b) Determine also, the initial pre-tension required in the belt.