2. Calculate the support reactions for determinate frame structure as shown. The supports A and B are both pin supports, and there is a hinge at C. Solve the reactions manually (following solution guidelines) using equilibrium analysis. Solve the internal forces values. 35 taym Ax Ay HINGE Bx By V max 3.75 2.5 Hy/m Amax Mmax 35m 3.S m

2. Calculate the support reactions for determinate frame structure as shown. The supports A and B are both pin supports, and there is a hinge at C. Solve the reactions manually (following solution guidelines) using equilibrium analysis. Solve the internal forces values. 35 taym Ax Ay HINGE Bx By V max 3.75 2.5 Hy/m Amax Mmax 35m 3.S m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reactions at node 1 using finite element method. You must use one beam element only that has 2 nodes and each node has 2 degrees of freedom (transverse displacement and rotation). Given that I = 8.33 x 10-6 m4 , A = 0.01 m2, a = L/5, b= 2L/3, E = 200 GPa, L = 2 m, F = 10 kN and M = 5 kN.m,
Using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. a=4.5 b=26.0 c=10 Determine: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.
The springs BA and BC each have a stiffness of 500 N/m and an unstretched length of 3 m. Determine the horizontal force F applied to the cord which is attached to the small ring B so that the displacement of AB from thewall is d = 1.5 m.
USING CONJUGATE BEAM METHOD Consider 150 mm x 200 mm (bxh) mm section and e = 80 GPa DETERMINE REACTION AT D Values: A = 9.4 M B = 5.5 kN/m C = 20 kN
Determine support reaction at B . Given P=100 Kn L=10 m
Use Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. a=4.5 b=26 c=10 Determine: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.
Two steel pipe columns (E=200,000??a,A1=2000mm2,A2=1800mm2)support a rigid beam AC that has a 3.6m overhang BC. The beam supports a linearly varying load of maximum intensity w=75K/nm as shownin the figure.Neglect the weight of the beam AC, and assume that the beam is supported on the two columns such that it transmits load to each column as an axial load.Determine the vertical displacementat end C of the beam, in column 1at A and column 2at B. Answer in mm.
the figure below has the following data: F1=1.7kN, F2=0.8kN, F3=0.58kN, a=1.33 meters, 36 degrees, belta=47 degrees. determine the reaction at b in kN. support A is a roller and Support B is hinge.
For the beam loaded as shown in the figure 2, determine the reaction at D in kN using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
Analyze by moment distribution. Modify stiffness as discussed in Section 11.5. E is con- stant. Draw the shear and moment curves.
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan