2. Draw the positive, negative, and zero sequence networks for the power system shown below.Use MVA base = 100, KV base 11KV at low tension side and 220KV at high tension side of transformEquipG₁T₁TL-1TL-2T₁G₂ofAVoltageRating11 KV11/220 KV220KV220KV11/220 KV11 KVWwwxxMVARating10010010010010010072-1X₁j0.2 pu10.1 puj0.1 puj0.1 puj0.075 puj0.19 pu00000X₂10.2 puj0.1 puj0.1 puj0.1 pu10.075 puj0.19 puXo10.05 puj0.1 pu10.35 pu10.35 puj0.075 puj0.05 pu29590

In this question we need to draw a positive sequence , negative sequence and zero sequence network…

2. Draw the positive, negative, and zero sequence networks for the power system shown below. Use MVA base = 100, KV base 11KV at low tension side and 220KV at high tension side of transform Equip G₁ T₁ TL-1 TL-2 T₁ G₂ of A conse Voltage MVA Rating Rating 11 KV 100 11/220 KV 100 220KV 220KV 11/220 KV 11 KV 100 100 100 100 72-1 X₁ j0.2 pu 10.1 pu j0.1 pu j0.1 pu j0.075 pu j0.19 pu 00000 X₂ 10.2 pu j0.1 pu j0.1 pu j0.1 pu 10.075 pu j0.19 pu Xo 10.05 pu j0.1 pu 10.35 pu 10.35 pu j0.075 pu j0.05 pu 20590

2. Draw the positive, negative, and zero sequence networks for the power system shown below. Use MVA base = 100, KV base 11KV at low tension side and 220KV at high tension side of transform Equip G₁ T₁ TL-1 TL-2 T₁ G₂ of A conse Voltage MVA Rating Rating 11 KV 100 11/220 KV 100 220KV 220KV 11/220 KV 11 KV 100 100 100 100 72-1 X₁ j0.2 pu 10.1 pu j0.1 pu j0.1 pu j0.075 pu j0.19 pu 00000 X₂ 10.2 pu j0.1 pu j0.1 pu j0.1 pu 10.075 pu j0.19 pu Xo 10.05 pu j0.1 pu 10.35 pu 10.35 pu j0.075 pu j0.05 pu 20590

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.23P: Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of...

See similar textbooks

Similar questions

Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
When working with balanced three-phase circuits, per-phase analysis is commonly done after converting loads to Y loads, thereby solving only one phase of the circuit. (a)True (b)False
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
The single line diagram of a power system is shown below. Load represented as impedance, (13.2) kV voltage It draws 60 MVA power from the system when it is below and (0.9) back power factor. Generators and transformers The related electrical parameters are given below. According to this; a) Calculate all impedances in this given circuit in pu and draw the equivalent impedance diagram of the circuit. (Select the base values as 100 MVA and 13.8 kV.) b) Since the voltage values of the generators are given as E1=1.1∟0° pu and E2=1.25∟10° pu, Calculate the value of the voltage (V1).
cotabato light and power company supplies two single phase transformers at san pablo area banked in open delta if each transformet is rated 75KVA capacity what is the maximum 3 phase load in kilowatts that the bank can carry without suffring oerload considdering that the load has laggingpower factor of 0.80
Two single phase transformer rated at 11,000/110V are used for scott connected transformers to supply two single phase electric furnaces with a rating of 500KW, 110V (teaser) 0.8pf and 700KW, 80V(main), unity pf respectively. If the supply 3 phase voltage is 11,000V, a. what will be the current flow in each of the three phase lines and b. what will be the KVA rating of each transformer c. If the net core area is 300cm2 and a flux density of 1.3 Wb/m2, determine the number of turns for each winding. Assume a 60Hz frequency
SHOW COMPLETE SOLUTION! ASAP!! two single-phase transformers are connected open-delta and deliver a balance three-phase load of 69.28kw at a pf of 0.8. calculate the minimum kva rating of each transformers
2. How two identical single phase transformers each of rating 5kVA, 200V/100V, 50Hz be used to stepdown a balanced 3-phase, 200V supply to a balanced 3-phase, 100V supply? Explain with circuit andphasor diagrams. Calculate also the maximum kVA that can be supplied from this connection.
Three 1-phase transformers each rated 75kVA are banked in delta and supplying a 3-phase load of 160kVA at 0.8pf lagging. If one transformer is removed for repairs, solve for the amount of kVA overloading of the remaining units. a) 10 b) 30 c) 20 d) 25