2. Find the moment of inertia and radius of gyration about the coordinate axes of a thin rectangular plate of constant density d bounded by the lines x = 3 and y = 3 in the first quadrant. %3D

Q: A flange coupling has 6 bolts with a bolt circle diameter of 200 mm is used to connect the steam…

A:

Q: a.) Determine the support's reaction. b.) Draw the Shear and Moment Diagram. c.) Determine the…

A:

Q: Consider an aligned fiber reinforced-polymer matrix composite for which the constituent fibers have…

A: Tensile strength is the highest load a material can withstand without cracking when stretched,…

Q: The uniform slender rod (6.7 kg) is pinned at point O. If a 7.6-g bullet shoots into the rod with a…

A: Given dataMass of the rod = M = 6.7 kgMass of the bullet = m = 7.6 x 10-3 kgSpeed of the bullet =…

Q: The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger…

A: Larger end: D1= 0.50 cmZ1= 7 mV1= 1.2 m/sP1= 5200 kN/m2 Smaller end: D2= 0.20 cmZ2= 3 m   To find:…

Q: What is the function of the folowing system. What is the benefit of vacuum boos Why is there a…

A: The vacuum booster is a metal canister with a diaphragm and a smart valve. On one side, a rod…

Q: Determine the value of displacement Force applied on wooden box=12 N Work done=24 J

A: Force applied on wooden box, F= 12 N Work done, W= 24 J   To find: Displacement, "d"

Q: Example 3: Draw the shear and moment diagrams for the beam. 2 kN/m 50 kN m A B

A: The stepwise procedure to draw the shear force and bending moment diagrams is shown in the following…

Q: A Carnot engine receives heat from source at 327°C causing an increase in entropy is equal to 5…

A:

Q: Solve for the pressure differential in Pa if the temperature inside a 3.47m vertical wall is…

A: Use pressure equation to solve this problem

Q: 400 lb/ft A C B - 4 ft- -4 ft- FIG. P4.7 | 10 KN t50 kN m A - 2 m 3m KIG PA 9

A:

Q: 1. Prepare an engine heat balance and distribution of energy table for the following test data…

A: Given;

Q: Josh threw the marble vertically upward with a speed of 70 ft/s from a bridge. On the way down, the…

A: Find Height of the bridge

Q: Given data: Force=0.5 N Displacemnt 1 m Determine work done

A: Given data : Force applied=F Displacement value=D   We have to calculate the value of work done

Q: A 30-kg disk with a radius of 0.7 m is pushed against a spring (k=900N/m). At the instant show where…

A: Given:- mass of disk,m=30 kg,radius of disk,r=.7 m,deformation in spring,x=.2 m,stiffness of…

Q: Is aircon-ditioner an example of thermodynamic system inside the house? Is it an open system, closed…

A:

Q: Calculate the partial pressure and gas-phase concentration (in ppm) of i-pentane in air when air at…

A:

Q: Explain and elaborate  bike interior is made of? and what are the components that made the interior…

A: Given Bike interior To find Bike interior material Internal strengthen components  Chemical example…

Q: Oz Oz V: find and du as functions of u and v if: z = 4e* In y , x = In(u cos v) , y =u sin v

A: Use chain rule to solve this problem

Q: The hydraulic cylinder imparts a constant upward velocity VA = 0.27 m/s to corner A of the…

A:

Q: Air enters a compressor operating at steady state at 14 lbf/in2, 60°F, with a volumetric flow rate…

A: The T-s diagram of the process is Given data, Pressure at state 1, P1 = 14 lbf/in2 Temperature at…

Q: H.W: find the angle between the planes x+ y = 1 and 2x + y - 2z = 2 29

A:

Q: The temperature of an air is at 30°C and is held at a pressure of 200 kPa absolute in a 500-liter…

A:

Q: calculate the boiler efficiency if the heat supplied to the steam is 26880 kj per kg of fuel burned…

A:

Q: 2. The half section of an arc is under a uniformly varying load. If the weight of the arch is 50,000…

A: The centroid of a body is the point where all sides have equal volume. The centre of mass of a solid…

Q: A 57.66mm constant diameter boiler tube uses water at 70 bar and 65°C. The substance leaves the…

A: Find , Inlet velocity of water in the tube. Assume  Adiabatic tube

Q: Find the initial velocity Final velocity=10 m/s acceleration=2 m/s2 time 3 s

A: Given data : Final Velocity=V Acceleration=a Time=t   Required : Initial velocity

Q: of of Find and for the functions: 2. f(x, y) = x² – xy +y² 4. f(x, y) = (x² + y² )

A: Use partial differential concept to solve this problem

Q: Given the image below, what is the magnitude of the equivalent concentrated load of the weight of…

A:

Q: With advances in technology, what do you think will be the changes in the contents of a Go-Bag 10…

A: You may need to survive on your own for several days after an emergency. To be prepared, you must…

Q: kı Jum 3 m₁ X₁ k2 w 3 92 m₂ X₂2₂ k3 mining

A:

Q: A specific oil has a Gs = 0.82. Solve for it’s a) specific weight in lb/ft³ and kN/m³ and its mass…

A:

Q: Consider an aligned fiber reinforced-polymer matrix composite for which the constituent fibers have…

A: Tensile strength is the highest load a material can withstand without cracking when stretched,…

Q: How  much heat must be supplied to water at 180 degrees celcius to make 1 kg of wet steam at 9000…

A:

Q: A- What is the system which used in Lorry braking ?, what is the advantages and dis advantages of…

A: Given question:What is the system which is used in Lorry braking? What is the advantage and…

Q: A uniform, 31.16-N rod is 14.45 n long carries a 415.01-N at its right end and an unknown weight W…

A: Weight of the uniform rod, Wrod= 31.16 N Length of the rod, L= 14.45 cm Load, P= 415.01 N Unknown…

Q: If a dom atydiatic tubing find the requiedtaqe e A shaft Conectad tthe tobin ananmer is being-sitet…

A: The torque required on the shaft is 2054.35 N•m.

Q: A sky lantern which a child tied to a piece of stone on the ground at the side of a tall multi-…

A:

Q: The 27-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r= 0.5 m.…

A: Givenm=27kgko=260mmr=0.5mF=354Nθ=6ot=3.2sg=9.81m/s2

Q: HW QI) Knowing that the coefficient of friction between the 25-kg block and the incline is μ = 0.25,…

A:

Q: forced draft centrifugal fan draws air at 1.32 cubic meter/sec towards a combustion chamber of a…

A: Write the given value of initial and final pressures and convert them into SI units. Here, P2 is…

Q: Find the y coordinates of points H and K. Yu = i mm YK = i mm Save for Later Using multiple attempts…

A:

Q: Calculate the forces, in Newtons, for the following 1.  member FG 2. pin H 3. hydraulic cylinder AB…

A: Given: The load, P = 789 N The angle, θ = 37.4°

Q: 7. Calculate the displacement at the free end of the inclined beam shown in Figure P3.7.Repeat the…

A:

Q: (Protit) What is the impact of decreasing/increasing radius kettle (m) with regarding to heat time?…

A: The ways by which heat transmission happens are equally as fascinating as the effects of heat…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm.…

A: Find the largest moment that can be required.

Q: if steam at 375 kpa , having a dryness fraction of 96% , is produced from saturated water at 375 kpa…

A: Given that: P = 375 kPa x = 0.96 state 1 = saturated liquid state 2 = liquid-vapor phase at P and x…

Q: Identify the advantage and a disadvantage of each tailplane; Inverted V-tail Inverted Y-tail Twin…

A: Inverted V-tail: The advantages of an inverted V-tail are: It decreases the weight of an aircraft…

Q: The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa;…

A:

Q: The hydraulic cylinder imparts a constant upward velocity VA = 0.27 m/s to corner A of the…

A: