2. From the figure shown, the piston and the weight W are at the same elevation. The face of the piston has an area of 13 cm while that of the weight is 30cm². The intervening passages are filled with oil having sp. gr. Of 0.80. What weight can be supported by a force of P=45 kg. applied at the end of the lever shown. 145 kg 3m W 012 См

2. From the figure shown, the piston and the weight W are at the same elevation. The face of the piston has an area of 13 cm while that of the weight is 30cm². The intervening passages are filled with oil having sp. gr. Of 0.80. What weight can be supported by a force of P=45 kg. applied at the end of the lever shown. 145 kg 3m W 012 См

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Piston A has a cross-section of 1516 cm2 while that of B is 773 cm2. B is higher than A by 7 m. If the intervening passages are filled with certain fluid having sp. gr. of 0.645 and a force of 8 kN is acting on B, what must be the pressure at piston A in Pa. Round your answers in 2 decimal places.
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown compute the magnitude of the force supported by the pin at C and the oil pressure p against the 3.58-in.-diameter piston of the hydraulic-cylinder unit AB.Assume a = 5 in., b = 33 in., c = 17 in., e = 36 in., and 26°. C=? LB p=? Lb/in^2
1st picture: Piston A has a cross sectional area of 1400 mm2 While that of piston B is 1000 mm2. B is higher than A by 2m. If the intervening passages are filled with oil whose specific gravity is 0.80 and a force of 4kN is acting on B. What must be the pressure at Piston B? Neglect the weight of the pistons.
The rectangular bin is filled with coal, which creates a pressure distribution along wall A that varies as shown, i.e., p = 4z1/3 lb/ft2, where z is in feet. Determine the resultant force created by the coal, and its location,measured from the top surface of the coal.
Hydraulics ProblemAn open horizontal tank 1.5m high 2m wide and 5m long is full of oil with a specific gravity of 0.9. It is accelerated in the direction parallel to the longer length at 2.3 m/s2 a. What is the force acting on the wall of the tank with the shortest depth in KN? b. If the acceleration is increased by 0.88 m/s2. Determine the volume of oil that spilled out the tank?Note: Draw free-body diagram and used 4 decimal places
Water is stored in a tank with an inclined panel AB whose dimensions are 2m long by 1.6m wide. The manometer indicates a gage liquid height of z = 1.2m. a. Determine the pressure (in kPa) at B. b. Determine the pressure (in kPa) at A? c. Apply the pressure prism concept in determining the force (in kN) exerted on side AB. d. At what distance from A (along the surface of panel AB) is the hydrostatic force acting? Your answer should be in centimeters.
If DA = 17cm , DB = 12cm and L = 4m , and if oil is flowing at a rate of 0.08 m3/s , determine the difference in pressure between sections A and B. Neglect head losses .
In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. Theweight of the gate is 4 kN and the force exerted by the stopper on the gate is measured tobe 80 kN.Please calculate the moment done by the resultant hydrostatic force about the hinge and the pressure on the water-oil surface.
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
5.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the vertical component of the hydrostatic force on the submerged curved section of the gate. Use unit weight of water 9.80 kN/m^3. fluid mechanics
Water is stored in a tank with an inclined panel AB whose dimensions are 5ft long by 6ft wide. The manometer indicates a gage liquid height of z=2 feet. Determine : a) pressure at B b)pressure at A c)apply the pressure prism concept in determining the force