Project: Band Stop Filter DesignThe Band Stop Filter, (BSF) is another type of frequency selective circuit that functions in exactlythe opposite way to the Band Pass Filter. The band stop filter, also known as a band reject filter,passes all frequencies with the exception of those within a specified stop band which are greatlyattenuated. By combining a basic RC low-pass filter with a RC high-pass filter we can form asimple band-stop filter that can block or at least severely attenuate a range or band of frequencieswithin the two cut-off frequency points.Project Deliverable 2This derivable illustrates criteria to proceed applying next steps of this project. Students have todo the schematic of the proposed circuit as well as the detailed design equations.Submit (below) a report with the following:1. The band stop filter block diagram.2. Hand calculation for different filter's components3. Detailed list of components and their values (use a table format).1. Block Diagram:2. Hand CalculationDesign a basic wide-band, RC band stop filter with a lower cut-off frequency of 200HZ and ahigher cut-off frequency of 900HZ.Rand SpRegoHa neTea oLow PaResponseResposetoCopyright © American College of the Middle East. 2020Page 2 of 4Figure 1: Band Stop Filter CharacteristicsAssuming a capacitor, C value for both filter sections (Cur, Cur) of 0.2uF, calculate the values ofthe two resistors, RLP and RHP using the formula:1. From the Low pass filter formula, Find Rup:1fi =2. From the High pass filter formula, Find Rup:fu = 2nRypCHP3. Calculate the center frequency (fc) and Bandwidth (BW):a. fe = Vfi x fub. BW = fu - fi

Answered: Image /qna-images/answer/c654855d-4fab-4b56-872f-d7cb973c3e45.jpg

2. Hand calculation for different filter's components 3. Detailed list of components and their values (use a table format). 1. Block Diagram. 2. Hand Calculation Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200Hz and a higher cut-off frequency of 900HZ. Rand Tream Ree Copyright American College of the Middle East. 2020 Page 2 of 4 Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (Cur, Cur) of 0.2uF, calculate the values of the two resistors, Rur and Rsp using the formula: 1. From the Low pass filter formula, Find Rur: fi 2. From the High pass filter formula, Find Rur: 3. Calculate the center frequency (f) and Bandwidth (BW): a. fe = Vfi x fu b. BW = fu- fi

2. Hand calculation for different filter's components 3. Detailed list of components and their values (use a table format). 1. Block Diagram. 2. Hand Calculation Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200Hz and a higher cut-off frequency of 900HZ. Rand Tream Ree Copyright American College of the Middle East. 2020 Page 2 of 4 Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (Cur, Cur) of 0.2uF, calculate the values of the two resistors, Rur and Rsp using the formula: 1. From the Low pass filter formula, Find Rur: fi 2. From the High pass filter formula, Find Rur: 3. Calculate the center frequency (f) and Bandwidth (BW): a. fe = Vfi x fu b. BW = fu- fi

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the distinction in voltage attain of a lowpass filter if the enter frequency is doubled? What is the distinction in voltage attain of a lowpass filter if the enter frequency is expanded ten times? How do you assemble a band give up RC filter? Simulate a circuit and generate a desk to show your claim.
Please provide Handwritten answer. Electrical Engineering It is a common practice to low-pass filter signals before feeding them into an A/D Converter. The purpose of this filter is to eliminate any noise or other frequency components beyond a useful frequency range. For instance, if you are recording ECG, you would low-pass filter it at 100Hz because there is no useful frequency components beyond 100Hz and if there is any component that would be noise. What problem arises during sampling of the signal by the A/D Converter if this pre-filter is not used? How does the sampling frequency need to be adjusted with and without the pre-filter? Answer the question considering Nyquist theorem.
A high-pass filter is to be designed for speech signal processing. The cutoff frequency is 3.4kHz and the gain to be 10.0 in the passband. At 340Hz, the gain is desired to be less than or equal to 0.1% of the gain at 3.4kHz. Please use Sallen-Key type of filters for this design and draw the complete circuit schematic and indicate the resistance and capacitance values.
You need an active lowpass filter that has a cutoff frequency of 500 Hz. If the stopband is defined as being -20dB from the passband, and you need this value to be reached at 600 Hz, please show three different filter options, and comment on their frequency and time domain characteristics. ..
As part of a radio receiver, you are asked to design a simple bandpass filter using a series inductor, capacitor and resistor. The filter needs to pass a centre frequency of f0 = 1089 kHz with a bandwidth of 9 kHz. Do this by finding the capacitor and resistor values together with a 240 uH inductor that will give you the correct centre frequency and bandwidth. Also, calculate the quality factor Q for your filter. Sketch the filter circuit and show all your calculations.
DESIGNPROBLEM_1. Using 10 nF capacitors and ideal op amps, design a high-passunity-gain Butterworth filter with a cutoff frequency of 2 kHz and again of at least −48 dB at 500 Hz.2. Draw a circuit diagram of the filter and label all component values.
Consider an anti-aliasing filter design using the Butterworth filter. The anti-aliasing filter feeds a DSP processor that has an Analog to Digital Converter (ADC) that can be configured to 8 bits or 10 bits. The sampling frequency of the ADC can be varied from 8kHz to 48kHz. You are using your Anti-aliasing filter + ADC pair to capture an analog measurement of a periodic signal with a maximum signal bandwidth of 3.4kHz. You decide to use the 8-bit ADC resolution at the lowest sampling frequency of 8kHz ( afterall the lowest sample freq of 8kHz satisfies the Nyquist criteria and you really are all about doing just the right amount of work!). What order must your Butterworth filter be? You relent and decide to use the max sampling rate of 48kHz. How does that decision change the filter order requirement of your Butterworth anti-aliasing filter? You decide that you want better resolution so you increase the ADC resolution from 8bit to 10bits. You also decide to keep the max sampling…
5, which milks the following conditions. design the Butterworth low-pass filter circuit. Specify the design process step by step. Draw the circuit you designed. Approximate the gain(dB)-frequency graph and mark its key points.a. Take your resistance values as 500 Ω, except for the gain multiple.b. cut frequency take fr as 4 × 1kHz. c. Take the gain value of the filter 4 × 5. Tip: 2. The Butterworth low-pass filter circuit of the order is as shown in Figure 1.
RLC bandpass design： The target is to filter out the square-wave noise from the 120kHz sinsousidal signal using the RLC banpass filter (series LCR configuration). 1- Derive the transfer function for the following second order LCR filter. 2- Derive an expression for the resonant frequency and the quality factor of the filter. 3- The objective is to filter out the square-wave noise from the sinousidal 120kHz signal. The two closest frequency components of the square wave must be attenuated at least by a factor of √2. We suggest you to use either a 10 mH inductor. Calculate the required Q and the repsective R and C to achieve the filter requirement.
Design the bandpass filter from using a cascade of a fourthorder low-pass Butterworth filter, a fourth-order high-pass Butterworth filter, and an inverting amplifier. The filter should provide an amplification of 2 within the band of frequencies between 100 and 10,000 Hz and use as many 2 kΩ resistors and 0.2 μF capacitors as possible.
a ) Using 0.1 pF capacitors , design an active broadband first - order bandpass filter that has a lower cutoff frequency of 200 Hz , an upper cutoff frequency of 2000 Hz , and a passband gain of 0 dB . b ) Write the transfer function for the scaled filter . c ) Use the transfer function derived in part ( b ) to find H ( wo ) where wo is the center frequency of the filter . d ) What is the passband gain ( in decibels ) of the filter at wo ?
DESIGNPROBLEM_PSPICEMULTISIMUsing a 5 mH inductor, design a high-pass, RL, passive filter with a cutoff frequency of 25 krad/s . 1. a) Specify the value of the resistance. 2. b) Assume the filter is connected to a pure resistive load. The cutoff frequency is not to drop below 24 krad/s. What is the smallest load resistor that can be connected across the output terminals of the filter?