2.) If the applied force P = 600 N and the coefficient of kinetic friction between the 55 kg crate and the inclined plane is M = 0.3 determine the velocity of the crate after it travels 8 m up the plane starting from rest. 30° 30⁰156 Ans. v 7.621 m/s

2.) If the applied force P = 600 N and the coefficient of kinetic friction between the 55 kg crate and the inclined plane is M = 0.3 determine the velocity of the crate after it travels 8 m up the plane starting from rest. 30° 30⁰156 Ans. v 7.621 m/s

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.79P: The coefficient of rolling resistance between the 30-kg lawn roller and the ground is r=0.1. (a)...

See similar textbooks

Related questions

Q: An oil pump operating at steady state delivers oil at a rate of 11 lb/s through a 1-in-diameter exit…

Q: D F 40° leter inc he 2000N 30° E 70° C *Final answers should be in 3 decimal places. But use all the…

Q: For a 1040 steel solid square bar, determine the endurance limit or Se based on the following…

Q: The Resultant Force and The angle of the Resultant Force with respect to vertical axis

Q: Air with an initial temperature of 18.03°C undergoes an isentropic process. After the isentropic…

Q: Use the spatial version of Grubler's formula to determine the number of degrees of freedom of the…

A: Given: To find: Degrees of freedom

Q: Determine the magnitudes of the components of the force FAB acting parallel to cable AC-Type the…

A: Given data :- Force along AB (FAB) = 20 lb. Find the magnitude of force parallel to line AC.…

Q: The open stream of water seen in the following picture emerges from a nozzle into the atmosphere at…

A: Given:Pressure at centerline of section 1, P1=101 kPaDiameter at 1, d1=12 cm=0.12 mDiameter at exit,…

Q: 3. A hydraulic lift is shown below. The combined mass of the piston, rack, and car is 4000 lbm. The…

A: Given: mass, M = 4000 lbm To find: Work done by pump

Q: A steam engine based on a turbine is shown in the figure below. The boiler tank has a volume of 100…

A: Given data as per the question The volume of the boiler tank =100 L Initial pressure of saturated…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: In the setup seen in the image, an oil tank's central circular opening is sealed off by a solid…

Q: A pressure difference of 750 millibar is applied across the legs of an equal leg manometer.…

A: Given:Pressure difference applied across the legs of the equal leg manometer, ∆P=750 mbar

Q: Match the model with the DE for that model or the model with the general solution for that model…

A: given; match the following;

Q: A 3 ft 200 lb 3 ft + -3 ft 5 30° 100 lb 50 lb Replace the loading system by an equivalent resultant…

A: Given:Forces acting:F1=200 lbF2=50 lbF3=100 lb

Q: A vessel contains water. The conditions of the system are: • volume of the vessel: V = 0.10 m³ •…

A: Given data Volume of vessel = 0.1 m3 Pressure = 200kpa Mass of water = 5 kg Specific volumes…

Q: Determine the phase for each of the following water states at 120◦C, 0.5 m^3/kg , show your…

Q: A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Neglecting the weight of the…

A: Given data: L=30 ftF=500 lbσ=20 ksi=20×103 psiδ=0.20 inE=29×106 psi Need to determine the the…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: A point of zero velocity. A. Critical Point B. Stagnation Point C. Inflection Point D. Triple…

A: Point of zero velocity is the point where local velocity of field is zero.

Q: To replace force-couple systems with an equivalent force by specifying the magnitude and direction…

A: F1=162lb F2=54lb M=550lb-ft To find resultant and it's inclination

Q: For the mechanism of the figure at the instant shown O1 is the center of curvature of the slotted…

A: Given Data W2= 10rad/s clockwise α2= 23rad/s2 counter-clock wise θ2= 44° β=52° O1O6=115cm O1O4=39cm…

Q: C B H 1 ft -6 ft- G₂ 2 ft D 6 ft 8 ft The platform assembly has a weight of 250 lb that may be…

Q: -2x Criven the shape above, Find the location of the Controid. Show all work.

A: Here, four shapes are visible so, No Shape Ai Xi Yi AiXi AiYi 1 Semi circle 5654.87 60 0…

Q: A silicon nitride rotor fractures at a stress level of 162 MPa. This material has a fracture…

A: Given:Stress level, σ=162 MPaMaterial fracture toughness, K=5.00 MPam1/2Geometric factor,…

Q: Replace the couple and force shown by an equivalent single force applied to the lever. Determine the…

Q: 2.4-16 A rigid bar of weight W = 800 N hangs from three equally spaced vertical wires (length L =…

A: Given data: A rigid bar of weight W =800 Nlength L= 150 mmdiameter of steel wire ds=2 mmdiamter of…

Q: At an annual rate of return of 8%, what is the future worth of $100 at the end for 4 years?

Q: Determine the equivalent spring stiffness constant of the following.

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

Q: For a large plate, the geometry factor, f, is 1.03. Suppose a steel casting alloy has a critical…

Q: calculate the discharge.

A: Since you ave asked multiple questions, we will solve the first question for you. If you want any…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: The internal shear force V at a certain section of an aluminum beam is 7.3 kN. If the beam has the…

A: The given information in the problem is listed in the following attached image:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: The given information in the problem is listed in the following attached image:

Q: Determine the x-coordinate of the mass cen the tapered steel rod of length L where the dia at the…

A: GIven

Q: In the figure, aluminum [E = 68 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

Q: PROBLEM 4 Determine the reactions for the beam shown below. 30016 100lb ift 2' R2 40016

Q: Carbon dioxide gas is compressed at steady state from a pressure of 18 lb/in² and a temperature of…

Q: EST. 4.121 Determine the sum of the moments exerted on the plate by the three couples. (The 80-lb…

A: Determine the sum of moments exerted on the plate.

Q: Compute the moment about point D.

A: Given data: F1=50 lbF2=150 lbM=500 lb.ft Need to determine the moment about the point D.

Q: Two (2) beams are subjected to different loading condition and position as shown. w1 w2 P x1 x2 x3 Ө…

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

Q: 3 12. Determine the absolute pressure at point B if the figure shown below if the density of mercury…

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: The given information in the problem is listed in the following attached image:

Q: When does an organization opt for contractual maintenance? Explain with examples. What are its…

A: Contract maintenance is done between the factory and the maintenance firm. All the machines in the…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

solve and show all steps. either partial or full answer is provided

2.)
If the applied force P = 600 N and the coefficient of kinetic friction between the 55 kg
crate and the inclined plane is M = 0.3 determine the velocity of the crate after it travels 8 m up
the plane starting from rest.
30°
Porb 00
30⁰ ha 156
Ans. v = 7.621 m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 10 kg block is subject to the action of a force that has the constant direction towards the spring, with a magnitude F= 250 (1 + x) N, where x is measured in meters. If the coefficient of kinetic friction between the block and the horizontal surface is 0.20, and ks= 50 N/m Use the springs por your calculations Determine: a) The work done by all the forces acting on the block during a movement from A to B. b) If the block starts from rest at point A, determine its velocity at point B using the equation of motion (Newton's 2nd Law). c) Verify the speed obtained in b) through the equation of work and Kinetic Energy. d) Explain the differences between the two methods used to find the velocity, from the point of view of the volume of calculations. Recomendations: 1. No force (except weight) is constant throughout travel 2. Acceleration is not constant at any point along the way. 3. When applying Newton's second law, it is advisable to do it in two sections. 4. Review the…
A 20-lb block slides down a 30° inclined plane with an initial velocity of 2 ft/s. Determine the velocity of the block in 3 s if the coefficient of kinetic friction between the block and the plane is U k = 0.25.
The position of a 5 kg object moving on a path is given by x = (0.25t3) m, y = (1.5t2) m, z = (7- 0.75t2.5) m, where t is in seconds. Determine the magnitude of total forces affecting the body when t = 3 s.
A trailer truck enters a 2 percent uphill grade traveling at 72 km/h and reaches a speed of 108 km/h in 300 m. The cab has a mass of 1800 kg and the trailer 5400 kg. Determine (a) the average force at the wheels of the cab, (b) the average force in the coupling between the cab and the trailer.
The 55 -lb crate is given a speed of 12ft/s in t=4 s starting from rest. The acceleration is constant. The motor has an efficiency ε=0.65 . Neglect the mass of the pulley and cable. (Figure 1 ) Determine the power that must be supplied to the motor when t=2 s . Express your answer in units of horsepower to three significant figures. (Gpt/ai wrong answer not allowed)
The 2.4-Mg car increases its speed uniformly from rest to 22 m/s in 38 s up the inclined road. (a) Determine the maximum power that must be supplied by the engine, which operates with an efficiency of ϵ = 0.8. Express your answer with the appropriate units. (b) Also, find the average power supplied by the engine. Express your answer with the appropriate units. Please use watts, not Mw for the final answer. Answer is not 38280 W and 18105.2 W.
If the coefficient of kinetic friction between the 50-kg crate and the ground isuk = 0.3, determine the distance the crate travels and its velocity when t= 3 s. The crate startsfrom rest, and p= 200 N.
3b At an amusement park, the bumper cars each have a mass of a. The riders have masses of b and c respectively. Car A is moving to the right with a velocity of 3 m/s to the right while Car B has a velocity of 2 m/s to the left. If the collision occurred in 0.06 s, determine the impulsive force of Car B on Car A. PIM: [include direction of the force] ma = 211 kg mb = 53 kg mc = 59 kg helloo very very urgent tysm
If the force exerted on cable AB by the motor is F = ( 110 t 3/2 ) N, where tt is in seconds, determine the 55-kg crate's velocity when ttt = 5 s . The coefficients of static and kinetic friction between the crate and the ground are μs = 0.37 and μk = 0.29, respectively. Initially the crate is at rest. (Figure 1)
The 10-lb block has a speed of 4 ft/s when the force of F= (8t^2) lbf is applied.Determine the velocity of the block when t= 2 s. The coefficient of kinetic friction at the surfaceis uk = 0.2
The 18 000-kg F-35B uses thrust vectoring to allow it to take off vertically. In one maneuver, the pilot reaches the top of her static hover at 200 m. The combined thrust and lift force on the airplane applied at the end of the static hover can be expressed as F = (44t + 2500t2)i + (250t2 + t + 176 580)j, where F and t are expressed in newtons and seconds, respectively. Determine how long it will take the airplane to reach a cruising speed of 1000 km/hr (cruising speed is defined to be in the x-direction only).
The 2.4-Mg car increases its speed uniformly from rest to 22 m/s in 38 s up the inclined road. (a) Determine the maximum power that must be supplied by the engine, which operates with an efficiency of ϵ = 0.8. Express your answer with the appropriate units. (b) Also, find the average power supplied by the engine. Express your answer with the appropriate units. Please use watts, not Mw for final answer.