2.) In the figure below the two boys push onthe gate with forces of FA = 30 lb and asshown. Determine the moment of eachforce about C. Which way will the gaterotate, clockwise or counterclockwise?Neglect the thickness of the gate.-6 ftB3 ftFBIn the figure above. If the boy at Bexerts a force of FB = 30 lb, determinethe magnitude of the force FA the boy atA must exert in order to prevent the gatefrom turning. Neglect the thickness ofthe gate.

Answered: Image /qna-images/answer/0cbbd129-b8dd-4c4b-9da1-7e90e17bad2e.jpg

2.) In the figure below the two boys push on the gate with forces of FA = 30 lb and as shown. Determine the moment of each force about C. Which way will the gate rotate, clockwise or counterclockwise? Neglect the thickness of the gate. -6 ft- B 60° FB А In the figure above. If the boy at B exerts a force of FB = 30 lb, determine the magnitude of the force FA the boy at A must exert in order to prevent the gate from turning. Neglect the thickness of the gate.

2.) In the figure below the two boys push on the gate with forces of FA = 30 lb and as shown. Determine the moment of each force about C. Which way will the gate rotate, clockwise or counterclockwise? Neglect the thickness of the gate. -6 ft- B 60° FB А In the figure above. If the boy at B exerts a force of FB = 30 lb, determine the magnitude of the force FA the boy at A must exert in order to prevent the gate from turning. Neglect the thickness of the gate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the vertical reaction at support D. Enter your answer in kN to two decimal places.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
The cylinder of weight, W, shown below is being hoisted up with the force F against the vertical wall. If us = 0.57 a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion W or W1 (in kN) = 516
In the gate AB is hinged at B and is 1.2 m wide. What vertical force, applied at the center of gravity ofthe 20kN gate, will keep it in equilibrium?
Determine the magnitude of the resultant forceacting on the corbel and its direction θ measuredcounterclockwise from the x axis.
What is the moment of the distributed load about the pin O? (a) 473 kN-m clockwise.(b) 338 kN-m clockwise.(c) 338 kN-m counterclockwise.(d) 270 kN-m counterclockwise.
Determine the force P needed to cause impending motion of the block.
The gate is 2.00 m wide and 1.00 m tall, supported by hinges and a guy wire. For F1 = 66.4 N, F2 = 87.8 N, F3 = 175 N, F4 = 109 N, find the torque resulting from each force about an axis through point P.
For the beam presented below:a) What is the degree of indeterminacy; b) Determine the moment reactions at the supports and draw the shear and momentdiagrams. (Solve by expressing the internal moment in terms of vertical reactionsat A and B, EI is constant). c) What would the shear diagram look like if a transverse load P was applied right atthe middle of the beam (Make a sketch of the new shear diagram). W (30kN/m) , L (1.9m)
Replace the loading (Figure 1) by an equivalent resultant force and couple moment at point O. Suppose that F1={8i−2k}kN and F2={−4i+5j−2k}kN. Part A Part complete Determine the resultant force. Enter the x, y, and z components of the force in kilonewtons to three significant figures separated by commas. Part B Determine the equivalent resultant couple moment about point O. Enter the x, y, and z components of the moment in kilonewton-meters to three significant figures separated by commas.
The overhead electric hoist C rides along a track on the horizontal beamAB. In addition to the 500-kN vertical force carried by the hoist, the beam alsosupports the three vertical forces shown. (a) If x = 5 m, determine the resultant ofthe four forces carried by the beam. (b) Determine the distance x for
In the figure on the right where there is a 50 N single load at point Bof the given rod system, (between AB: 4m / BC: 1m)a) find the support reactions?b) Immediately after support A, just before point Band immediately after and just before the C-bracketFind the cross section effects by cutting?c) Draw the cross sectional influence diagrams.