2. In your own words, explain :a. What is reactive power?b. What is average power?c. What is instantaneous power?3. For Fig 1 is shown a pure resistive circuit.Discovery wave-generator values and resistors acquired with your components kit. Averagepower must be P=13mW. Vin must be less than 5Vpp. Choose one value and get the Vrms foryour calculations.Design the circuit according to your AnalogVin= Vrms1000 HzR10°Fig 1a. What is R1 value?b. What is Vp value?What is Vpp value?С.d. What is Vrms value?e. Show your calculations and equations used.

As per the guidelines of Bartley we supposed to answer first question only for solution of remaining…

Answered: 2. In your own words, explain : a. What…

Engineering

Electrical Engineering

2. In your own words, explain : a. What is reactive power? b. What is average power? C. What is instantaneous power?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Find Z for the maximum average Power transfer to the Lead for the circuits Shown below. JIr

Q: is the RMS value of output voltage of the step down chopper which is having 240 V as a input for a…

Q: Determine the average power that is being supplied or absorbed at each element. R, +, R$2052 100°…

A: In an AC circuit, the average power is only consumed by resistor in the AC circuit and the average…

Q: An Alternating Voltage is given by: v(t)= 300 sin (200 πt – 0.437) Volts Find the: (a) Amplitude,…

A: We need to tell about given signal voltage, frequency, RMS value and time period

Q: A single-phase AC voltage controller has a resistive load R = 10 Ohm, and %3D the RMS input voltage…

Q: Harmonic Frequency 50 Hz 250 Hz 350 Hz 450 Hz Current Amplitude 5A 2.1 A 1.5 A 0.8 A The current…

A: Given,

Q: Find the real power, reactive power, and the complex power delivered by the source.

A: In this question , we will find real power , reactive power and complex power...

Q: The distorted waveform in power distribution system contains only odd-harmonic components O True…

Q: ermine the following, . Amplitude i. Frequency ii. RMS value of Voltage Figure Al

A: Bartleby has policy to solve only first 3 subparts of a question. So reupload the question

Q: A step-up chopper is operated at a frequency of 4KHZ with a supply voltage of 215V and a control…

A: The step up circuit given is shown in the figure attached. The frequency at which the switch S…

Q: Which of the information given about the governer (speed regulator) element in the power plant is…

A: Which of the information given about the governer (speed regulator) element in the power plant is…

Q: A step- down dc chopper has a resistive load of R=152 and input voltage 200V. when the chopper…

Q: Vz = 8 V, Vs = 0.6 V, V1 = 2 V. Find the average dc voltage of output waveform. Please write your…

A: We need to check which diode will be on or off for given input . We will find out output voltage .

Q: is the RMS value of output voltage of the step down chopper which is having 200 V as a input for a…

A: Given Input Voltage, Vi= 200V Duty cycle, D= 70% =0.7 Duty cycle = output voltage/ input voltage

Q: A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of…

Q: ——- is the RMS value of output voltage of the step down chopper which is having 230v as a input for…

Q: An ac generator with a maximum voltage of 24.0 V and a frequency of 60.0 Hz is connected to a…

A: Given data, The value of maximum voltage is Vmax = 24 V. The value of frequency is f = 60 Hz. The…

Q: A generating station has a demand of 25 MW, a load factor of 60%, then the average demand will be:

A: Given: A generating station has, Maximum demand = 25 MW Load factor = 60 % Average demand =?

Q: 4. The AC generator in the circuit shown below supplies voltage with amplitude 5.0 V at frequency…

A: Given V=5 V f=336 Hz

Q: Q3. For the power electronic circuit shown in figure below, sketch the output voltage Vo, Find the…

Q: p(t) Watt 1200 1000 800 600 400 200 10 -200 -400 Time (msec) Q Zoom image O Frequency 50 Hz Average…

Q: What is the peak voltage across R2? b) What is the RMS value of I1?

Q: B) A voltage given by v(t) = 230sin314t is applied to series circuit and the resulting current is…

Q: A single phase full wave ac/ac converter's input voltage Vs (rms)=220 volt. The firing delay angles…

Q: The reactive power output of an alternator is limited by load angle True False

Q: e Figure below, calculate Z₁.

A: MOSFET (Metal–oxide–semiconductor field-effect transistor)- It is a type if transistor which is…

Q: A factory draws a lagging load of 2000 kW

A: Active Power- It is power utilized by the load. It is the power factor times the apparent power of…

Q: Determine the load (a)rms voltage and (b) average load current when the conduction angle is 30…

Q: The short circuit characteristic of an alternator is always non- linear O True O False

Q: The voltage represented by e = 240 Sin(377t) volts is connected across a 20 ohms resistor. The RMS…

A: In this question we will find RMS value with given voltage and current....

Q: Three phase system eliminates which of the following harmonic component or components in the…

A: Need to find three phase system eliminate which harmonics

Q: Determine the normalized power and energy for each of the following signals:

A: Answer : (a) x1t=e-2tu(t) standard form of x1(t) is given by x(t)=e-atu(t) t>0 And it…

Q: 1. Build the following circuit, Use the function generator to obtain the specified AC input voltage.…

Q: where x= RMS value of the signal to be quantized x. 2x max 2

Q: A 120V source control power to a 5 Q resistive load using a phase control switch. If the load power…

A: As the 120V source feeding the 1KW load using a phase controlled switch, one can use single SCR…

Q: The average or mean value of a symmetrical alternating quantity is the average value measured over a…

A: Need to find true false

Q: 1) Find Uab(t) and its rms value. [voltage across A and B] 2) Find the realpower of voltage source.

Q: 169sin 377t a) What is the RMS value? b) What is the Average value?

A: Given: Let V=169sin 377t

Q: Two equal voltages are out of phase with respect to each other by 90 electrical degrees. If the…

Q: Calculate the rms value of the output voltage of an AC-AC converter with the following…

A: First we will draw the output of the ac voltage converter and than we will find RMS voltage.

Q: a. What is the complex power, S= b. What is the reactive Power, Q=. c. The power factor, PF= and the…

A: a. From the given diagram, the values of the real power and reactive power can be written as The…

Q: is the RMS value of output voltage of the step down chopper which is having 220 V as a input for a…

A: In this question , we will finf output RMS voltage of opamp...

Q: 3. Replace the DC source by an ac source with an rms value of 12 V. Connect it across the same bulb.…

A: Vrms=12V f=60Hz Rlamp=12 ohms.

Q: Problem 4.13: For the AC voltage shown, determine the (a) amplitude, (b) peak-to- peak voltage, (c)…

A: In practical scenario the alternating voltage is generated which is of sinusoidal nature and is…

Q: FIND THE VALUES INDICATED AND SHOW THE COMPLETE SOLUTION. RMS Phase Angle Peak Instantaneous Average…

Q: EX1: The AC Voltage controller shown below is used for heating a resistive load of 5 N and the input…

Q: If the angular frequency of an alternating voltage is w, then the angular frequency of instantaneous…

A: In the question, frequency of alternating voltage is given find the frequency of instantaneous…

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.

Question

2. In your own words, explain :
a. What is reactive power?
b. What is average power?
c. What is instantaneous power?
3. For Fig 1 is shown a pure resistive circuit.
Discovery wave-generator values and resistors acquired with your components kit. Average
power must be P=13mW. Vin must be less than 5Vpp. Choose one value and get the Vrms for
your calculations.
Design the circuit according to your Analog
Vin= Vrms
1000 Hz
R1
0°
Fig 1
a. What is R1 value?
b. What is Vp value?
What is Vpp value?
С.
d. What is Vrms value?
e. Show your calculations and equations used.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sinlge phase load consist of a coil having a resistance of 10 Ω and an inductance of 100 mH. The coil is connected to a 150 V, 50Hz AC supply. Determine: (i) the impedance of the coil ; (ii) the current drawn by the coil; (iii) the apparent power; (iv) the active ower; (v) the reactive power; (vi) the power factor. (vii) also draw the power triangle and label all the values.
Two equal voltages are out of phase with respect to each other by 90 electrical degrees. If the resultant is 311 Volts, what is RMS value of each one?-write legibly-show the complete solution
The average load of a dairy plant at 11 kV, 50 Hz is 950 kW at 80 percent power factor but the maximum contract load of plant is 1200 kW. As per local electricity regulating authorities norms, consumer must keep the power factor of 95 percent to avoid any poor power factor penalty. Determine the following (i) Rating of capacitor bank (in kVAr) (ii) The capacitance of the capacitor bank (in micro Farad) (iii) Explain why the power factor becomes low and how the capacitor bank will assists to improve the power factor?
A 240-V rms 60-Hz supply serves a load that is 10 kW (resistive), 15 kVAR (capacitive), and 22 kVAR (inductive). What is the current drawn from the supply in amperes? And what is the required capacitor rating in microfarads required to improve the power factor to 0.96 ?
1) Determine the total current supplied by the source and the current in each branch. 2) Sketch a fully labelled phasor diagram showing all voltage and currents in the circuit. 3) Determine the active power delivered by the source voltage. 4) Determine the reactive power. 5) Sketch the power triangle. 6) Comment on the significance of the power factor and briefly state how it can be improved.
a) To the coil of a henry, measure its internal resistance and the value of the inductance.b) Measure the effective voltage and current at the terminals of the 100 Ω resistor and at the source.c) Measure the average power delivered by the source.Note the phase shift between the supply voltage and the voltage across the 100 Ω resistor (only at this point).
Calculate:Reactive, apparent and active power of the circuit, consider the power supply 120V rms and a frequency of 60 Hz.
A series circuit containing a noninductive resistance of 3 Ω and a coil is connected to a 120 V, 60 Hz supply. The current is 25 A. The true power, as indicated by a wattmeter, is 2500 W. Determine: the power factor of the series circuit. the effective resistance of the coil. the impedance and inductive rea ctance for the coil. the power factor of the coil
In the circuit below, if the inductance L is large enough to operate in continuous current mode. a) Draw the waveform of the output voltage and mains current for the 45 degree trigger angle when the switch S is in transmission. b) Average value of output DA voltage VDC1 when switch S is open, output DA when switch S is closed (in transmission) If the average value of the voltage is VDC2, calculate the value of VDC1 / VDC2. Lesson: power electronics please quick
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by π/3 radians and the total line current is 23.4 amp. (rms), determine the current in B.
A 15 KVA closet transformer lovated inside a building is used to step down the voltage for the buildinh. It is connected to a primary "Z800" V AC power source. The ratio of the number of primar windings to the number og secondary windings on the transforemer is 60 to 15. 1. what is the voltage provided to the building? 2. What is the amoung of current provided to the building? 3. If the building consymes 3200W of power, what is it's power factor? 4. What is the phase angle of the secondary power source in the building?
A. Find the average power absorbed by the load in the circuit. Use positive value if the power is absorbed and negative value if the power is delivered. B. Find the reactive power absorbed by the load. Use positive value if the reactive power is absorbed and negative value if the reactive power is delivered. C. Find the apparent power for the load.