2. The frame shown in the Figure is unbraced, and bending is about x-axis of the members. All beams are 18 x 35 and columns are 12 x 58. а. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. If Fy =36 ksi is the stiffness factor applicable to these columns? C. 20 20 12' C 12' B 12'

2. The frame shown in the Figure is unbraced, and bending is about x-axis of the members. All beams are 18 x 35 and columns are 12 x 58. а. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. If Fy =36 ksi is the stiffness factor applicable to these columns? C. 20 20 12' C 12' B 12'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
Determine the maximum magnitude of load P that can be applied to the truss. The maximum allowable tensile force in the members of the truss is (Ft) max = 5.2 kN, and the maximum allowable compressive force is (Fe) max = 3 kN. Take d = 2 m. (Figure 1) Figure 1 of 1 E d/2 C PV d/2 <
On the study roof truss shown in the figure, determine the force in element F G and ineach of the elements located to the right of F G. Also, indicate in your answer if the elements are intension or in compression.
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp
From the beam shown, fc' = 28 MPa, fy = 414 MPa, βh = 1.20, Cc = 40 mm. Take D = 25 mm diameter size. a) Determine the value of maximum spacing
A variable cross-sectional beam is pinned from the point B by BD bar as shown. Flexural rigidity of AB and BC beams are 2El and EI, respectively. If the axial rigidity of the BD bar is EA, Determine the reaction forces at the point A by using, Mohr method 7 AL ). 3 EA L P E2I C EI
Q - 1 ; Determine the deflection equation for beam supporting load shown in Figure below, also determine maximum deflection, flexural rigidity of the beam is EI. W R R 2 2
Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the loading. Forces are positive if in tension, negative if in compression. A Answers: AB= AH= BC= CD= CF = CG= CH= BH= i DE= DF= EF= 5.5 m FG = GH- i i i i i i i i i i i i B 4.7 m H 31 kN 5.5 m C 5.5 m G 63 KN D 5.5 m F 31 KN KN kN Ξ Ξ Ξ KN KN 2 KN KN KN KN KN KN 2 KN 2 E
The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 10 kips is applied. Use Est = 29 x 106 psi and Ebr = 12 x 106 psi. %D Steel Bronze A В C e-3 ft - 2.5 ft 1.5 ft VP
Compute the deformation of the beam using area method:E= 200 GPa I= 1000 x 106 mm4
Two non-slender braces (A and B) resist lateral load in a story of a braced frame. The lateral stiffness of brace A is three (3) times higher than that of brace B. Select all true statements. ✔ The magnitude of axial force in brace A will be three times larger than that in brace B The horizontal component of axial force in brace A will be three times higher than that in brace B The axial force will be equal in braces A and B ✔ The horizontal component of axial force will be equal in braces A and B
For the beam shown below, the ratio of stiffness coefficients k41 and k43 is Assume El is constant. -2m- B 4 3m 2