Answered: 2. When compounded quarterly P12,000…

Engineering

Civil Engineering

2. When compounded quarterly P12,000 becomes P 20,415.23 after 4 yrs. What is the nominal rate of interest?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter20: Engineering Economics

Section: Chapter Questions

Problem 5P

See similar textbooks

Related questions

Q: Given data : U=2 m/s a=3.2 m/s2 t=4 s Find final velocity of car

A: Given data : The initial velocity of car is denoted by U The acceleration of car is denoted by a The…

Q: Examples and explanations of the following coordinate systems are provided. • Object Coordinate…

A: Answer :- Object Coordinate System:- When a modeller constructs an object in a modelling programme,…

Q: 5. Determine the reactions at the supports A & B. see Figure 5. |5 KN /m Figure 5 t to 2.5m 20m 2-0m

A: Reaction at support A is 11.805 KN Reaction at support B is 66.944 KN

Q: What is the vital role of Geology in civil engineering projects? What is the major concern of…

A: 1. What is the vital role of Geology in civil engineering projects? Answer:- 1. For Civil…

Q: The cable supports the three loads shown. Determine the sags ys and yp of B and D. Take Pi = 800 N,…

Q: With reference to Figure RN-21, an eccentric compressive load is applied to the rectangular column…

Q: Derive the internal forces equations ( N, Q & M) at any section ( S) for part a-c and find its…

A: Solution: From the given three hinged arch derive the internal forces

Q: A 25 cm diameter sewer when running full carries a discharge of 0.08 m/sec. What will be the…

A: given- 25 cm diameter sewerdischarge when running full=0.08 m3/s

Q: The data are given as follows: Weight of evaporating dish: 53.5430 g Weight of evaporating dish and…

Q: A block of rock has edge length (0.94m ,1.26m ,1.15 m ) the grain density is 2.87 g/cm3 find the…

Q: Using Virtual Method Determine the vertical deflection at A. E = 200 GPa and I = 1000 x 106 mm 10…

Q: An oil storage tank 35 m in diameter is located 2 m below the surface of a deposit of clay 32 m…

Q: Determine the value of degree of saturation Specific gravity32.7 void ratio=0.34 water content=0.23

A: Given, Specific gravity, G = 2.7 Void Ratio, e = 0.34 Water content, w = 0.23 To determine: degree…

Q: A solid sphere (diameter 6 mm) is rising through oil (mass density 900 kg/m3, dynamic viscosity 0.7…

Q: A half-closed clay layer is 8 m thick and it can be assumed that cv=ch. Vertical sand drains 300 mm…

Q: Solve the reactions for the beam 60 kN 120 kN-m 20 kN/m C 2 m 2 m 2 m 2 m A. Reaction at B B.…

A: L = 8m P = 60KN w = 20KN/m M = 120KNm

Q: у-аxis Figure for Problem 1 Note: Each square indicates 1 square unit (0,0) х-аxis

A: Solution Find the area of the composite figure Divide the area into small areas like A1, A2, A3,…

Q: 1. Transportation and moving How many 5-ton LCY dump trucks will it take to support a wheel loader…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: SITUATION. A pressure vessel 300 mm in diameter is to be fabricated from steel plates. The vessel is…

A: Pressure vessel A pressure vessel is a container that is designed to hold gases or liquids at a…

Q: Calculate the moment of resistance of a doubly reinforced T- beam as shown in Fig. 7.9 having a…

Q: can you explain how to do this in cad. using the details below. Can you like specify the dimensions…

A: Given data,

Q: Method of Superposition 1. Estimate the deflection at point C and the rotation at point B. EI is…

Q: P C B d.

Q: A strip footing of width 3 m is founded at a depth of 2 m below the ground surface in a (c - 0) soil…

Q: Problem 2 Solve the reactions for the frame and draw the shear & moment diagram for each member. 22…

A: Apply Equilbrium equation. RE is less because loading is try to rotate the structure about E hence…

Q: Calculate the moment of resistance of a doubly reinforced T- beam as shown in Fig. 7.9 having a…

Q: If the origin point and the corners of the traverse have the following coordinates. Find the lengths…

Q: Example select a mix proportional of 28-day compressive strength (measured on standard cubes) of 44…

A: w/c ratio = 0.55 (maximum) Cement Content = 290kg/m3 Water Content = 0.55 Cement Content = 159.5…

Q: Determine the value of degree of saturation Specific gravity32.7 void ratio=0.34 water…

Q: .A raft foundation 60 X 40 m carrying a net pressure of 145 kN/m^2 is located at a depth of 4.5 m…

A: Raft foundation : Raft foundations are made consisting of a thick concrete slab resting on a huge…

Q: A sphere 900mm-diameter floats half submerged in a tank of oil (sg=0.90) What is the total vertical…

Q: Explain why oxygen depletion occurs when organic waste is disposed directly in the lake. And mention…

Q: Find the value of work done if force of 2N displace the wooden box by 1.22

Q: Problem (7.2): The surface of an airplane wing is subjected to plane stress with normal resses a, Oy…

A: The given data is shown below: θ=30°σn=35 MPaθ=50°σn=10 MPaσx=100 MPa

Q: A cube with a side of 550 mm. What force is required to completely submerged the cube in water if…

Q: What is the maximum value of Shear force you could design a W21x68 beam to carry?

A: Solution-W 21×68 beam We have to determine the maximum value of shear force

Q: A cylindrical tank, 1.20-m diameter and 2.50m high weighs 2850 N. The tank float in water with a…

A: Diameter of cylinder, D=1.2mHeight of cylinder, H=2.5mCylindrical tank is floating with a draft of…

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: TF1=20, BF1=3x20=60, Tw=20, Dw=8x20=160, TF2=20, BF2=10x20=200, D=a+8a+a=20+160+20 = 200

Q: example of soil test and its procedure

A: Considering the Proctor compaction soil test: A process in which a soil is subjected to mechanical…

Q: A river 5 m deep consists of a sand bed with unit weight of 20 kN/m3. Y. = 9.81 kN/m3. The effective…

A: Saturated density and depth of river is given and it has been asked to determine effective stress 5…

Q: QeAFin d The (fEM) a wi (6 12

Q: ora linear stress variation over the base of the dam and neglecting hydrostatic uplift. 70m note: sg…

Q: Table provides the incremental rainfall depth every 10 minutes from a rainfall station during a…

A: Duration of storm = 2hours Maximum depth for storm duration of different time period has been found…

Q: 3. A scoop carries 610 kg of load with center of mass at G. Neglecting the mass of the members,…

Q: Calculate the maximum shear stress amay in the web of the T-beam shown in the figure if b = 14 in.,…

Q: A boundary liņe runs across a 75m wide road reserve as shown on the diagram below. From the data…

A: Solution From the diagram, Sin θ = 166.97(138.807+69.483) θ = 530 17' 7.23'' So, , ∠CAD = 1800 -…

Q: Please refer to the figure shown below. If P is equal to 6,720 lb., and if all the rods have a…

Q: Draw shear force diagram

A: Finding support reaction at A: Applying equilibrium condition Taking moment at point B ∑MB=0…

Q: Problem Statement Calculate the moment of inertia and radius of gyration about the x-axis for the…

Q: 2) A rectangular (5ft by 8ft) foundation will be built on the soil profile shown in the figure.…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

2. When compounded quarterly P12,000 becomes P
20,415.23 after 4 yrs. What is the nominal rate of
interest?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the problem with complete solution. 2. If 60,000 is due at the end of 4 years at 5% compounded annually. What is its present value?
At 7.8%, a bridge cost P220M with a life of 18 years. The bridge must be partially rebuilt at a cost if P90M at the end of each 18 years. Calculate the capitalized cost if an annual maintenance of P590,000 is required.
compare theaccumlated values at the end of 10year if P100 is invested at a rate of 12% compounded annually, semi-annually , quartely, monthly, daily and continuously
wouldn't Ix3 have to deducted according to the figure?
Need full soluition. Note: US gallon/min
How much should be invested to have 7000 pesos after 190 days when invested at 9% simple interest? (1 year = 365 days) (Numerical answer only and whole number, example: 7811)
The delta of crop is 67 cm. Calculate the duty if the base period of the crop is 180 days.
The probability in percent of a 150 year return period not to occur within the next 45 years is?
Equipment for immersion cooling of electronic components has an installed value of P 819,000 with an estimated trade-in value of P 25,000 after 15 years. Using Declining Balance method, what is the total depreciation at the end of 7 years?
You bought a new car which you intend to use as a public utility vehicle for P950,000. The expected life of the car is ten (10) years for its intended use. Your driver and you agreed that for the first five (5) years , your “boundary” is P1,500.00 per day and P1,000.00 per day for the rest of its economic life. You also expected a repair and maintenance costs of P30,000 every six (6) months from year one (1) to five (5) and P50,000 from year six (6) to ten (10). At the end of 10 years you can sell the car for P100,000. If your MARR on invested capital is 15% every (6) months, determine whether this is a good investment. Use the AW, PW, or the FW method in your solution. Indicate all other assumptions you use in your analysis.
Flood damage in any year is given according to the following table. With your combined knowledge on probability and engineering economics, what is the present worth of flood damage for a ten year period? use 6% as the effective annual interest rate. Damage Probability 0 0.75 10,000 0.20 20,000 0.04 30,000 0.01
24 If $210 is deposited in a savings account at the beginning of each year for 3 years and the account draws interest at 4.2% per year, compounded annually, the value of the account at the end of 3 years will be most nearly Express your answer in whole number.