2. Write the minimum amount (Asmin. or p min) of reinforcement required for R.C. Beams and R.C. Columns. Which one needs more steel reinforcement, why? 3. Write minimum clear cover for slab, beam and column, why clear cover to be provided? What is the difference between clear cover and effective cover, explain with sketch?

2. Write the minimum amount (Asmin. or p min) of reinforcement required for R.C. Beams and R.C. Columns. Which one needs more steel reinforcement, why? 3. Write minimum clear cover for slab, beam and column, why clear cover to be provided? What is the difference between clear cover and effective cover, explain with sketch?

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter32: Drawing Framing Plans

Section: Chapter Questions

Problem 32.1Q: What are the two major methods of determining lateral loads?

See similar textbooks

Similar questions

3. A reinforced concrete beam is 0.25m x 0.450 m (b x d). The tension reinforcement provided is 2H25 (As = 982mm2). Determine the moment of resistance of the section if fck = 25 N/mm2 and fyk = 500 N/mm2. 4. By using the information from Q3, calculate the actual area of reinforcement required.
The layout of a 200 mm thick unrestrained slab over a proposed single garage has internaldimensions of 6000 x 3000 mm and supports a live load of 1.5 kN/m2. It is supported by 230mm thick walls. The environmental conditions are mild, and 1 hr fire rating is required.Determine the suitable reinforcement and check the code requirements for shear, minimumarea of reinforcement and bar spacing.Assume deflection is ok (no need to check), fcu= 30 MPa, fy = 450 MPa and Ø 12 mmreinforcement bars for effective dep
What are the two major methods of determining lateral loads?
for the floor system shown below with assuming that service dead load 3 kN/m?, live load 4 kN/m², Answer the following: 1- Classify the floor system into one way or two-way slab. 2- Check the proposed slab thickness according to deflection and shear requirement. 3- Check the proposed reinforcement at top and bottom in direction shown below. 4- What is the ultimate load transfer from slab and brick wall on beam AB? f = 28MPa , fy = 400MPA and y for brick wall = 17kN/m
Design the largest interior and edge panel of the slab for the plan system shown below (Follow the Direct Design Method for the slab analysis). fc′ = 4 ksi fy = 60 ksi. Height of building = 10′, Column dimensions = 12″ x 9″ . Live Load 75 Psf, Additionaldead load =100 Psf. Assume any other necessary data by yourself. Provide drawings of the slab. Consider is one case that the slab is flat without any beams and in another case it has beams 12 inch deep and 9 inch wide. Try to optimize the design as much as possible.
Derive the equation for the minimum percentage of lateral reinforcement for spiral columns? Derive the equation for the actual percentage of lateral reinforcement for spiral columns
Problem - A 5.5m x 6m slab has main reinforcements running in both directions. Estimate for the materialsneeded for steel works using 12mm∅ x 9m spaced at 11cm.
The recommended steel ratio for a slab having thickness of 125 mm is 0.00215 determine the required area (mm2) of main reinforcement bars using 12 mm dia. bars and minimum clear cover. Round of your answer to a whole number, no need to write down the unit.
PLEASE HELP ME WITH WITH COMPLETE SOLUTION. Please use nscp 2015 A beam that is to resist an ultimate moment of 935.6 kN·m is restricted to a 355.6-mm width and 609.6-mm total depth. Using fc′ = 34,473 KPa and fy = 344,750 kPa, determine the area of reinforcement.
trength of Materials under floor framing Please solve with complete solution ???
In need clear steps pls
How to determine the design loads.