2.121 A container of weight W is suspended from ring A, to which cables AC and AE are attached. A force P is applied to the end F of a third cable that passes over a pulley at B and through ring A and that is attached to a support at D. Knowing that W = 1000 N, determine the magnitude of P. (Hint: The tension is the same in all portions of cable FBAD.) 1.20 m Z 0.78 m 0.86 m Fig. P2.121 с 1.60 m B F y A E W D 0.40 m 1.30 m 0.40 m X

2.121 A container of weight W is suspended from ring A, to which cables AC and AE are attached. A force P is applied to the end F of a third cable that passes over a pulley at B and through ring A and that is attached to a support at D. Knowing that W = 1000 N, determine the magnitude of P. (Hint: The tension is the same in all portions of cable FBAD.) 1.20 m Z 0.78 m 0.86 m Fig. P2.121 с 1.60 m B F y A E W D 0.40 m 1.30 m 0.40 m X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.4. Two cables are tied together at C and loaded as shown. Knowing that P= 360N,Determine the tension in cable BC and AC. 1 Free-body Diagram only
The rigid bar AB is supported by a cable BC and a pin at A. The diameter of the cable is 16 mm and themodulus of elasticity is 200 GPa. Calculate the vertical movement of the point B knowing that P=15kN
A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that approximately loads the cable by a uniform q(x) = q0. If l (small letter L) = 10 m, hA = 5 m, and hB = 4 m. Compute the maximum force in the cable for its minimum distance to the group by 3 m. q0 (kN/m) 12.213
A cable is attached to the 20 kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
A cable is attached to the 20-kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
The rectangular beam ABC, 133 mm wide by 322 mm deep, is supported by a pin at A and the cable CD. Determine the normal stress (in MPa) at the bottom of the beam and at asectionofthebeam 1.07 m from the pin if P = 499.99 kN.
A man weighing [(70*B)+(8*E)] N stands at the middle rung of a steel ladder uniformly weighing [15+(4*A)] kN/m. Assuming that the floor and wall are perfectly smooth and that slipping is prevented by cable CD, determine the following: A. Tension in the cable B. Reaction at A and B the values are A=3 B=9 C=1 D=3 e=1
A 90-lb load is suspended from the hook shown . If theload is supported by two cables and a spring having a stiffnessk = 500 lb/ft, determine the force in the cables and the stretch of thespring for equilibrium. Cable AD lies in the x–y plane and cable AClies in the x–z plane.
The wall crane supports a load of 700 Determine the horizontal and vertical components of reaction at the pins at A and D. Also, what is the force in the cable at the winch W?
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
2. Forces (Figures Needed) 2.4. Two cables are tied together at C and loaded as shown. Knowing that P= 360N,Determine the tension in cable BC and AC. 1 Free-body Diagram only
The vertical mast OA, which weighs 1.5kN, is supported by a ball-andsocket joint at O and by the cables AB and AC. Calculate the tension in each cable when the 20-kN force is applied.