2.68 The homogeneous gate shown in Fig. P2.68 consists of one-quarter of a circular cylinder and is used to maintain a wa- ter depth of 4 m. That is, when the water depth exceeds 4 m, the gate opens slightly and lets the water flow under it. Determine the weight of the gate per meter of length. 1m Pivot FIGURE P2.68 4 m

2.68 The homogeneous gate shown in Fig. P2.68 consists of one-quarter of a circular cylinder and is used to maintain a wa- ter depth of 4 m. That is, when the water depth exceeds 4 m, the gate opens slightly and lets the water flow under it. Determine the weight of the gate per meter of length. 1m Pivot FIGURE P2.68 4 m

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.16P

See similar textbooks

Similar questions

A 3-m wide, 8-m high, rectangular gate is located at the end of a rectangular passage that is connected to a large open tank filled with water as shown below. The gate is hinged at its bottom and held closed by a horizontal force, FH, located at the center of the gate. The maximum value for FH is 3500 kN. (a) Determine the maximum water depth, h, above the center of the gate that can exist without the gate opening, (b) Is the answer the same if the gate is hinged at the top? Explain your answer. [Answer in units of ft. for part (a)]
A rectangular tank 6 m long, 3 m wide and 2m deep contains water to a depth of 1 m. It is accelerated horizontally at 2.5 m/s2 in the direction of its length. A. Determine the net force due to water acting on each end of tank. B. Determine the minumum pressure intensities at bottom C. Determine the slope of the free surface
An open tank contains 5.7 m water covered with 2.8 m kerosine (y= 8.0 kN/m^3). Find the gage pressure at the interface and at the bottom of the tank.
A 5m long, 2m wide and 2m high tank is filled with water. a. Solve the resultant hydrostatic force at the base.b. solve the resultant hydrostatic force on the wider wall.
Required : 1. Hydrostatic force F1 2.hydrostatic force F2 to keep the gate in vertical position 3. The density of liquid P2=?
An open tank 1.8 m. by 1.8 m. and 1.3 m. deep contains water at a depth of 0.90 m. The weight of the tank is 3500 N. The tank is acted by an unbalanced force of 12000 N parallel to a pair of sides. Determine: a. Acceleration of the tank b. Max pressure at the bottom of the tank c. Force acting on the side with greatest depth
6.3 Determine the wall shearing stress in a pipe of diameter 100mm, which conveys water. The velocities at the half the diameter from boundary is 2 m/s. The local velocity at 20mm from the pipe wall is 1.5m/s and the flow is turbulent,
1. A barrel contains 0.2-meter layer of oil floating on water that is 0.4 millimeter deep. If the density of the oil is 600 kg/m^3, find the gage pressure at the oil-water interface. 2. A dam having a triangular section has a vertical face 30m high and base 15m wide. Use SG= 2.4. Determine the height of water that could rise on the vertical side of the dam so that the location of the resultant force is 5 meters from the toe.
Opening of a gate A square of side L=0,6 m controls an upstream water depth of H=12 m ( Figure 1) 1) Determine the hydrostatic force acting on the gate 2) Determine the location of the pressure center 3) Calculate the force P required to open the door
A vertical, trapezoidal gate in the face of a dike is subjected to sea water pressure (s = 1.3) on one side. The upper edge is in the water surface and is 1.577 meters long. Two edges are vertical and measured 2.77 meters and 3.77 meters each. Determine the total pressure on the gate and the location of the center of pressure.
A pipe bend tapers from a diameter of 500 mm at inlet to a diameter of 250 mm at outletand turns the flow through an angle of 45°. Measurements of pressure at the inlet andoutlet show that the pressure at inlet is 40kN/m2 and the pressure at outlet is23 kN /m2 . If the pipe is conveying oil which has a density of 850 kg/m3 , determine themagnitude and direction of the resultant force on the bend when the oil is flowing at therate of 0.45 m3⁄s. The bend is in a horizontal plane.
determine the value of the maximum positive momment at F for a moving live load fo 21 kn/m