2021-03-16 Q13. A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, 200 GPa, as = 11.7 x 10/°C) and portion BC is made of brass (E, = 105 GPa, a, = - 6/°C). Knowing that the rod is initially unstressed, determine the compressive force induced in ABC when there is a temperature rise of 50°C. 20.9 x 10

2021-03-16 Q13. A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, 200 GPa, as = 11.7 x 10/°C) and portion BC is made of brass (E, = 105 GPa, a, = - 6/°C). Knowing that the rod is initially unstressed, determine the compressive force induced in ABC when there is a temperature rise of 50°C. 20.9 x 10

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 15 mm, and a length of 5.5 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 45°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
i need the answer quickly
A steel plate is used to connect a column and beam as shown in Fig. 3. The connection betweenthe beam and the plate is fillet welds. Given Q=150kN and Mx= -5kN-m (applied at centriod ofthe welds between the beam and the plate), determine maximum shear stress in the welds betweenthe beam and the plate.
Aluminum Bronze Steel 2P 3P P 4P - - 1.0 m 0.8 m FIG. P2.16 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses pre- scribed in the table are not to be exceeded. A (mm²) E (GPa) G, (MPa) Вronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140
A stepped shaft has the appearance shown in Fig 5-13. The region AB is aluminum, having G= 28 GPa, and the region BC Is steel, having G- 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60 mm outside diameter and 30-mm inside diameter Determne the maximum shearing stress in the aluminium in MPa if a torsional load ot 4000 N m is applied at B. Ends A and Carerigidly damped. 45 mm 60 mm 30 mm 12m
Determine the stress experienced by the member if it is cooled and heated from room temperature.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Find the stress produced in rod due to tensile load of 2.02 N whose cross section area is 2 mm2
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe.