21. Given i = 0.5 sin a, determine i at a = 72°.
Q: can you help me with this problems from Bioengineering signals and sensors class?
A: To solve this problem, let's first analyze the circuit.a) Complex Gain Formula Derivation:The…
Q: Part A In the circuit shown in (Figure 1) the batteries have negligible internal resistance and the…
A: First, we need to understand the problem. We are given a circuit with several resistances and two…
Q: Please answer all subparts please answer in typing format
A: Step 1: Step 2: Step 3: Step 4:
Q: Please don't use matlab please answer in typing format
A: Output:0: zerosx: poleslocus(diamond):s = 1.24s = -7.24
Q: Exercise 11.6 Design a passive, low-pass filter with corner frequency around 400 Hz and input…
A: To design a passive low-pass filter with a corner frequency of around 400 Hz and an input impedance…
Q: Q2 (1). In Figure 2-1, two curves represent fault currents supplied by two sources in case of phase…
A:
Q: #1. The open-loop gain of an op amp is 50,000. Calculate the output voltage when there are inputs of…
A: Given data:Non inverting terminal voltage: V1=20μVInverting terminal voltage: V2=10μVOpen loop…
Q: I need help checking if my answer is correct 1) Using superposition, determine the current through…
A:
Q: Please help thank u
A:
Q: thanks!
A:
Q: A circuit has 375 μS of conductance. Calculate the circuit resistance
A: Approach to solving the question:The relationship between the conductance (G) and resistance (R) is…
Q: Calculate io in the circuit of the figure applying mesh analysis.
A: KIRCHHOFFS VOLTAGE LAW:It states that the algebraic sum of voltages and their voltage drops are…
Q: 3.23. Determine the stability for each of the following linear systems. a. y(n) b. y(n) = == Σk=0…
A: to determine the stability of two linear systems described by their respective equations: a.…
Q: A discrete system described by the following difference equation y(n) = x(n)-0.9x(n-1)- 0.1x(n-2)…
A: Step 1: Step 2: Step 3: Step 4:
Q: Problem 1 For the network shown in Figure 3.1: a) Find Is. b) Find the average power delivered to…
A: Step 1:Step 2:
Q: Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz.
A: X-rays contain extremely high energy and short wavelengths, allowing them to penetrate a variety of…
Q: Please answer in typing format for
A: To find the amplitude, frequency, phase angle, and phasor V of the sinusoid v(t)=6cos(5t+17):…
Q: Can you check if the thevenin equivalent of Zth that I got is correct The Zth I got was: Zth =…
A: Step 1: Step 2: Step 3: Step 4:
Q: (d) Find ₁ and ½ in the circuit in figure 5 852 w 40A 692 π 2002 552 w Figure 5.
A: Thank you
Q: Find the transfer function, G(s) = Vo(s)/Vi(s) for the electrical network below. 0000 2 H + Vo(t)-…
A:
Q: 4. a) Determine the maximum effective area of a Hertzian dipole of length 10 cm operating at 100…
A: the information you provided, I can help you solve for the current through resistor R_2 (10Ω) and…
Q: Please help me to solve this question Thank you in advance...
A: (a) A cycloconverter is a type of power converter that directly converts AC power frequency to…
Q: Notes: - Use 2 decimal and round the 3rd decimal. Example : 13.225 , your…
A: Hi student,Please modify your question. We, tutors, can only see the notes or instructions. We…
Q: I need a handwritten solution from the expert. Thank you.
A: Approach to solving the question:Answer it on my best of skillsDetailed explanation: Examples: Key…
Q: 8.15. Design a second-order bandstop digital Chebyshev filter with the following specifications:…
A: Step 1: Step 2: Step 3: Step 4:
Q: Use the timing waveform to describe how a clocked flip-flop responds to asynchronous inputs.
A: The flip-flop is a J-K flip-flop, here's how a clocked flip-flop responds to asynchronous…
Q: Please answer in typing format
A: Step 1: The general equation of a parameters is:V1=a11V2+a12I2&I1=a21V2+a22I2 Step 2:…
Q: Need Asap in Hand written form. Please Don*t send chatgpt Answers, Although you can use for your…
A: The feeder impedance is given as 0.50 + j1.3502. This complex impedance indicates that the feeder…
Q: Find the output impedance at 104 rads/sec. Vin (t) w 4 ΚΩ ib 50 ib 0.005 μF w 50 ΚΩ w 15 ΚΩ
A:
Q: UX design problem: Design a logic circuit that has (3) signal inputs: A1, A0 Select (S) 1.…
A: Truth Table:We have 3 inputs: A1, A0, and S.The output, Z, is not specified. So, we need to…
Q: Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz plz plz please…
A: Step 1:Step 2:Step 3: Step 4: Final plot:Computer generated root locus for verification:
Q: Q2: Determine Zi, Z., and A, for the network of +22 V ifr₁ = 33 k. #10:1 91 MO 2.2 ΚΩ ΓΕΩ Η ΜΩ…
A:
Q: Can you check if my answer is correct? 1) Find the Thevenin equivalent circuit for the portions of…
A: Step 1: Step 2:
Q: Please answer question 1
A: a.) No Load voltage (Ea)Ea = V + IaRa Where:Ea = No load voltageV = Terminal voltageIa = Armature…
Q: Can you check if the Zth that I got is correct The Zth I got was: Zth = 754.88 + j628.32 Zth =…
A:
Q: Hi there, I need help with this control systems question.
A: Step 1: Step 2: Step 3: Step 4:
Q: A- AB C- Figure P4.14 F2 Figure P4.15 F1 4-11. Analyze the two-output combinational circuits shown…
A: Step 1: One thing which you can identify very easily by looking at the gates is their type, AND, OR,…
Q: I need an expert solution correctly handwritten.
A:
Q: Consider a convolutional code with code rate R = 1/2, k = 1, and constraint length L = 3. The…
A: Step 1: Step 2: Step 3: Step 4:
Q: do the full calculation on how you got to the right answer so i can fully understand how it is meant…
A:
Q: Problem Find IB and Ic in the circuit shown in Figure 4. Considering RB = 50K, Rc = 1.5K, Vcc = 20V,…
A: Step 1:Step 2:Since transistor is in cut-off mode Hence all current are zero.Step 3: Step 4:
Q: Using Nodal Analysis, determine the voltages at nodes (1, 2 and 3) of the circuit shown in Figure…
A: Step 1: Step 2: Step 3: Step 4:
Q: Q6) A three-phase to single-phase, three-pulse cycloconverter delivers power to a load rated at 100…
A: b) Input Voltage and Power Factor EstimationEstimating the input voltage (Vi) and power factor…
Q: Design a circuit that controls the passage of a signal "A" with the specifications: 1. Output X will…
A: +--------+ A ---->| XOR | | Gate | +--------+ B ---->|…
Q: 2257 IPA m 7. A. Find the typical dc operating point for the circuit below using the transfer…
A:
Q: all parts please
A: Step 1: Answer of (a)…
Q: Q5: A liquid-level system has a cross-sectional area of 3.0 ft². The valve characteristics are q = 8…
A:
Q: 13. The following expression describes a carrier modulated by a sine-wave message. CN=13) o(t)=cos…
A: Step 1:Step 2:Step 3: Step 4:
Q: 14. A satellite allocates a frequency band from 2000 MHz to 2040 MHz for transmission of digitized…
A: Step 1:
Q: Please answer in typing format
A: Calculating the Magnetic Field Strength (H)The magnetic field strength (H) in amperes-turns per…
Step by step
Solved in 2 steps
- What is the complex expression for a given alternating current i = 250 sin(wt-25 deg)? a. 227 + j106 b. 160 - j75 c. 227 - j106 d. 160 + j75A current is given by i = 8 sin 377t. What is the frequency?Express answer as a whole number.244. The apparent power drawn by an a.c. circuit is 20 kVA and reactive power is 12 kVA. The real power in the circuit in kW will be
- Given the Figure 3 as shown below, determine: R a) Draw the Phasor diagram in terms of: 250 2 1. Voltage phasor 2. Impedance phasor 120 V 60 Hz L 650 mH b) Instantaneous e and i equations. c) Draw the waveforms showing e and i sine waves. 1.5 uF Figure 3 ellAnswer is 2.93 hz. Take No. Of poles = 2.Find the rms values for v = 120 V sin(377t + 15°) and i = 8.5 x 10- A sin(2rt + 65°).
- A complex number is represented as Z=4+j3 ohm. What will be magnitude and phase of this complex number?PA.7. Reduce each of the following to rectangular form: a. Za = 5 + j5 + 10/30° b. Zh = 5/45° - j10 10/45° c. Zc 3 + j4 15 d. Za 5/90A solenoid with an inductance of 0.25 H and a resistance of 100 Q is connected to a 120-V 60-Hz source. The current is: Please check the closest answer that applies. X L 120 V 60 Hz O0.226 2-16.3° A O0.224 2-31.2° A LO