22. The three-jaw universal chuck can be used to hold Select one: a. HEXAGONAL AND ROUND WORK b.0CTAGONAL WORK c.SQUARE WORK d.OCTAGONAL AND ROUND WORK

Q: Angle between side cutting edge and axis of tool is known as: * Back rake angle Side rake angle Side…

A: Answer: The correct answer is option (c) side cutting edge angle.

Q: It carries the cutting tool and precisely controls its movement either parallel to the ways ,called…

A: Option d is correct.

Q: In drilling operation on lathe machine, the drill bit is fixed in O a. Carriage O b. Headstock С.…

A:

Q: QUESTION 6 When facing the spindle, which direction should a right-handed cutter be rotated in order…

A: The turning tool can be divided into 3 categories, namely  Left-handed tools Right-handed tools…

Q: Advantage of Mechanical chucks is:         a/ High accessibility       b/ Good flexibility       c/…

A: advantages of mechanical chucks are It provides flexibility  in changing workpieces   . It has a…

Q: By what the size of upright drill press is identified?   a)largest-diameter cut b)largest-diameter…

A: Upright drill machine  An upright drill machine is used to drill the workpiece vertically. In this…

Q: 1. Sketch and explain any six work holding devices used on drilling machine?

A: 1)work-holding device; Because of the forces being created when drilling, all workpieces must be…

Q: 23. The four-jaw independent chuck can hold Select one: a.ROUND WORK ONLY O b.SQUARE WORK ONLY…

A: Four jaw chuck can hold all of the mentioned shaped by adjusting the individual jaws.

Q: QUESTION 2 A 4-fluted endmill is always center-cutting. O True False

A: The 4 fluted endmills are used for milling harder material. But with the increase in the number of…

Q: Surface grinders are used to produce the Select one: O a. Flat surfaces O b. Hole on surface O c.…

A: Surface Grinding is the operation performed in Grinding process. It is a finishing process by using…

Q: 26. When a two-fluted end mill is used to cut a slot, the maximum depth of cut should be Select one:…

A: Option a is correct.

Q: Advantage of Collet chucks is:

A: Given:- Collet chuck   To find:- Advantage

Q: Advantage of Shrink fit chucks is:         a/Easy handling       b/High pull out security…

A: Option b is correct.

Q: In which of the following machining operation, motion of workpiece is rotary and motion of cutting…

A:

Q: On increasing the value of rake angle, the strength of tool

A: GIVEN DATA SOME STATEMENT ABOUT RAKE ANGLE IS GIVEN WE HAVE TO CHOOSE CORRECT OPTION

Q: Tool post is situated on the top of O a. Carriage b. Tail Stock c. Feed rod d. Head stock

A: In a lathe machine, the tool post is the part in which carries or holds the tool. And this tool post…

Q: e type of chuck most suitable for holding ctangular chuck is

A:

Q: 2 Types of lathe chuck 2 Classification of lathe tool holder 2 Types of shaper

A: Given question: Types of Lathe Chuck Classification of Lathe Tool holder Types of shaper The given…

Q: Disadvantage of taper turning by taper turning attachment method is that only limited taper angles…

A:

Q: d. Down milling

A: Option (d) is correct. Down Milling

Q: an a thick saw blade be used as a broach. Why. Why is it difficult to make

A: As per the guidelines we are subjected to solve only one question at a time. Please repost the same…

Q: Chuck in lathe machine is located in ________________. a.

A: Chuck is used to hold the workpiece and clamp it against the tool force. chuck is mounted on…

Q: Plunge turning is most suited for:         a/ Rough grooving when the depth is bigger than the width…

A:

Q: 3. Define the tools that must have during the Shaper Machine Operation.

A:

Q: L the Cutting edges on both the end and outside periphery of the In cutter. * Down milling Face…

A: Ans) : Face Milling

Q: In drilling operations, drill chucks are used for holding the work piece. Select one: True False

A: The above statement is false

Q: Identify the part of a lathe machine which is used to give lateral feed motion for the tool. a)…

A: Option a is correct

Q: - Three-jaw chuck -Mandrels

A: given :irregular shaped workpiece clamping devices

Q: Angle between side cutting edge and axis of tool is known as: Back rake angle O Side rake angle Side…

A: Angle between side cutting edge and axis of tool is given as Side cutting edge angle or side cutting…

Q: The advantage of an independent chuck is that it is easy to work with. Select one: True False

A: A chuck is a machine component that is used to hold the workpiece in the predefined position in such…

Q: 8-In lathe, the carriage and tail stock are guided on.. a) Same guideways. b) Different guideways.…

A: Solution:

Q: Which type of cutting tool used in lathe machine? Select one: O a. Multipoint cutting tool O b.…

A: Lathe Machine: A machine is used for the machining processes such as Turning, step turning, cutting,…

Q: In this horizontal column and knee type machine cutter rotates about axis

A: The answer is a) Horizontal axis.

Q: 1. In face milling. the axis of the cutter is tangent to the surface being milled. (a) true or (b)…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: In toolbit nomenclature, the point where the primary and secondary cutting edges met. a.…

A: The edge on tool which removes material is known as cutting edge of tool. Single point cutting tool…

Q: In carpentry, the type of saw to be used to work inside a narrow hole or slot is O A. Hack saw O B.…

A:

Q: Angle between side cutting edge and axis of tool is known as: Rack rako anglo

A: Given:Lathe tool has so many angles and edges. All the edges has different work.

Q: The type of taper turning method in which the tool follows a diagonal path by engaging the too…

A: Data given-  Taper : the taper shaped defines as the shape which area is gradually increase or…

Q: In which of the following taper turning method the tool follows diagonal path

A: Tail stock set over:- Here, tail stock is set by required offset and tool feed in parallel to the…

Q: In which cutting process single point cutting tool removes material from a rotating workpiece to…

A: In turning process the workpiece rotates in the lathe machine and the single point cutting tool is…

Q: Differentiate three jaw and four jaw chuck with simple sketch?

A:

Q: With respect to four jaw chuck design, Which of the following statement is correct?

A: Answer 1  c) Four jaw self centring chuck is used to hold hexagonal shape objects Answer 2 d) To…

Q: Lathe chuck mounted on which part of a lathe machine?

A: Lathe machine has several parts but lathe chuck which is a rotating part is mounted on,

Q: End mills have cutting teeth .? O a. On the sides O b. At one end O c. At the face d. On the face &…

A: End mills cutters are the cutters with similar shape as of drill bit.

Q: It is a hardened steel device with a taper shank on one end and a 60 point at the other end (a) Live…

A: Lathe machine is used for manufacturing process. On which number of operations are performed such as…

Q: The advantage of an independent chuck is that the work can be centred to high precision. Select one:…

A: Advantages They can be utilized to hold sporadically molded parts. With the utilize of a dial…

Q: In lathe machine, Work piece is held in the work holding device called 'Chuck' and the chuck is…

A: