23. If the specific weight of liquid is 8.0 KN/m^3, its density is * 815.50 kg/m^3 8.16 kg/m^3 815.50 g/m^3 815.50 g/cm^3 24. A liquid has a dynamic viscosity of 4.8 x 10^-4 lb-sec/ft^2 weighs 54 lb/ft^3. Its kinematic viscosity in the SI is * 2.66 x 10^-2 m^2/s 2.66 x 10^-1 m^2/s

23. If the specific weight of liquid is 8.0 KN/m^3, its density is * 815.50 kg/m^3 8.16 kg/m^3 815.50 g/m^3 815.50 g/cm^3 24. A liquid has a dynamic viscosity of 4.8 x 10^-4 lb-sec/ft^2 weighs 54 lb/ft^3. Its kinematic viscosity in the SI is * 2.66 x 10^-2 m^2/s 2.66 x 10^-1 m^2/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: With the aid of annotated sketch, discuss slot and plugs welds used in the construction of high…

A: Step 1 Asked about: use off slot and plug welds in infrastructure projects with a sketch.

Q: Question A direct shear test was conducted on a cohesionless soil (c = 0) specimen under a normal…

A: Given- Cohesion- C=0,σ=normal stress=200 kN/m2,shear stress τ=100 kN/m2,

Q: Problem 3.5 - Given the cable tension T = 80 lb, determine a) the moment about point A due to T, and…

A: To determine the, a) Moment about A due to T b) Shortest distance from point A to line BC.

Q: Size (mm) 0.25 0.149 0.075 0.052 0.02 0.01 0.004 0.001 pan Weight retained (g) 18.96 33.18 45.03…

A: According to the question calculate the percentage retained (whole number)?

Q: Give some insights and reflection about the "Occupational Safety and Health Policy and Safety…

Q: Q4: A beam 20 m long is loaded as shown in Figure below. The supports are so low that the reaction…

A: We need to find X1 and X2 Conditions R1=R2 Equilibrium of forces Equilibrium of moments

Q: 2.15 Compare the following three roof structures. All three have the same span length and the same…

Q: 10m 6 m. Z6m -6 m- 4m -8m B F 8m Determine lo siguiente: 1. El momento con respecto al origen: Mo =…

Q: Matt Murdock's triangular lot was measured using a 10 – m steel tape which was found to be 0.05 m…

Q: 5) Calculate the following slope distances (hint: the distance equation shown in lecture slides is…

A: Latitude is the projection of a line in north south direction where as departure is the projection…

Q: blem 2. The cross-sectional area of the beam is 1250 mm The diameter of at supports is 25mm.…

A: Diameter of pin at B=25mm To find shear stress at point B

Q: A body is launched straight upwards with an initial velocity of 1400 ft/s. what is its velocity at…

Q: 1. Find the mass density of helium at a temperature of 4°C and a gage pressure of 184 KPa, if the…

Q: A water tank is to be placed on the moon as part of an on-going space mission. It is in the shape of…

A: The hydrostatic force exerted by a fluid on the body is given as:- F= P ×A where P= ρgh is the…

Q: The three cables shown are used to support a 45 kg flowerpot. Determine the tension force determined…

Q: A cantilever retaining wall is required to support a backfill having the following soil properties:…

Q: 2.13 Consider a rectangular reinforced concrete beam. Draw a diagram showing the beam internal…

Q: . Prove the following: √√fc' 1.4 4 fy fy p min = -¹ (1-1-² 2mR Mu As fy (d-a/2)

Q: Relation of communication in architecture List 3 review of related literature

Q: (Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the…

A: To find out the two manometer reading h, and H.

Q: 1. Compute the magnitude of the slope at the left support and the deflection 1m. left of the right…

Q: Q-A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an…

Q: For the stressed elements allocated to you, find the values and sketch the orientations: a) Maximum…

A: Given data, Compressive stress along the y-axis, σy = -80 MPa Tensile stress along x-axis, σx= 40…

Q: Q.23. The prinicipal stresses at a point across two perpendicular planes are 75 MN/ m² (tensile) and…

Q: 850 N/m 2.5m

A: Given Diameter= 300 mm

Q: Air is drawn into a wind tunnel used for testing automobiles as shown in the figure below. (a)…

Q: Q- What is the rapid sand filter surface area required for filtering of 10 MLD water assuming a…

Q: Describe all illustrate the different Destructive and Non Destructive test in construction materials…

A: This question comes from construction material and design Here asked about the differences between…

Q: The Froude number of flow in a rectangular channel is 0.8. If the depth of flow is 1.5 m, the…

Q: 24: A beam 20 m long is loaded as shown in Figure below. The supports are so le at the reaction is…

A: We need to find X1 and X2 Conditions R1=R2 Equilibrium of forces Equilibrium of moments

Q: Water flows over the spillway shown in the figure below. If the velocity is uniform at sections (1)…

A: Given: Required: Flowrate per unit width

Q: Question 3: Consider the power transmission-line tower shown in the accompanying figure. Is this…

Q: Water flows steadily with negligible viscous effects through the pipe shown in the figure below.…

A: Given: Required Diameter at outlet

Q: 7. . Find the grain-size (gradation) distribution of the following: a. Original dry mass of sample…

A: Answer We need to find percent finer in each sieve based on the given retained weight and plot grain…

Q: What is rock's maximum principal stress? (A) 262.47 kPa (B) 262.37 kPa 262.27 kPa (D) 262.57 kPa

Q: failure was observed to be 10kPa. Find the tangent of the angle of shearing resistance of the sandy…

Q: IFRS Foundation?

A: Comes from the estimation of costing and financing of the project in civil engineering This question…

Q: Calculate A) the position vectors rAB and rac and B) The magnitude and direction angles of the…

Q: Question- mmm A mild steel specimen is under uni-axial tensile stress. Young's modulus and yield…

A: Given data- Young modulus- E=2×105 MPa, Yield stress- σy=250 MPa, To Find- The maximum amount of…

Q: Water flows steadily with negligible viscous effects through the pipe shown in the figure below.…

Q: Give some insights and reflection about the New Horizons Safety Engineers "Organizational Structure"…

Q: What is the specific difference between a standard double-pitch roller chains and standard roller…

A: Roller chain is a kind of conveyance chain that is commonly used for the transference of useful work…

Q: Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher…

A: Objective: To choose the correct alternative for the given statement. Given: Which of the…

Q: Q-A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an…

A: To find out the ultimate resistance of pile.

Q: Draw the shear force and bending moment diagram for the compound beam shown in the figure. Assume…

Q: 2. of dred minutes due to a storm. At the outlet of the catchment, the stream draining the catchment…

Q: Gasoline flows steadily downward through th pipe shown in the figure below. Viscous effect are…

A: D1=D2=0.12ft D3=0.1ft P1=0 To find discharge and pressure

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

A: To find out the maximum shear stress developed in steel.

Q: Size (mm) 0.25 0.149 0.075 0.052 0.02 0.01 0.004 0.001 pan Weight retained (g) 18.96 33.18 45.03…

A: A sieve analysis (or gradation test) is a practice or procedure used in civil engineering and…

Q: Problem 3.1 - Determine the moment about the center of the bolt at point A due to the given 50-N…

A: Given data in question Load 50 N Angle 30° Length 200 mm To find out Moment at A

Concept explainers

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.

Question

23. If the specific weight of liquid is 8.0 KN/m^3, its density is *
815.50 kg/m^3
8.16 kg/m^3
815.50 g/m^3
815.50 g/cm^3
24. A liquid has a dynamic viscosity of 4.8 x 10^-4 lb-sec/ft^2 weighs 54 lb/ft^3. Its kinematic
viscosity in the SI is *
2.66 x 10^-2 m^2/s
2.66 x 10^-1 m^2/s
2.66 x 10^-3 m^2/s
2.66 x 10^-4 m^2/s
2.66 x 10^-5 m^2/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.) A volume of 3 cu. meter of water is subjected to a pressure increase of 17 MPa Compute the change in its volume in m3 if it has a bulk modulus of 2755 MPa.
The ocean's pressure at a depth of 9.9 km is 7a,bc MPa. Recognizing that the unit volume weight of the ocean at the surface is 10,abc kN /m^3, the modulus of elasticity for the pressure change between the ocean surface and a depth of 9,a km is 2,abc GPa; a) find the change in the specific volume between the surface and the 9,a km depth of the ocean. b) find a specific volume at a depth of 9,a km. C) find a unit volume weight at a depth of 9,a km.
The density of a steel anchor is 4205 kg/cu.m that is attached to a cylinder with 0.60m diameter, height of 1.2m, and with a mass of 34kg that floats in water with its axis vertical(upright). The steel anchor is attached to the cylinder which causes it to be submerged to a depth of "h" meters and remain in equilibrium position. a) Determine the equation based on the relationship between the weight of the anchor, "Wa" and the submerged depth "h". b) What is the required weight of the anchor that will submerge the cylinder to half of its length in Newton? c) What will be the maximum possible anchor weight which will keep the cylinder afloat in kg?
A 1060 kN cube (3m each side) floats in a 1.8m depth of water which is on top of the mercury layer. a. Determine the vertical distance from the top of the cube to the interface of water and mercury. b. If a load of 760 kN is added to the weight of the cube, what is the distance from the top of the cube to the water surface?
Soil in a 2.000 m wide x 2.000 long and 1.125 m deep container weighs 7,435 kg (7.435 x 103 kg) when completely dry. The soil is watered until it is fully saturated. After several days the soil drains to field capacity and weighs a total of 8,473 kg (8.473 x 103 kg). Assuming the density of 2650 kg/m3 (2.650 x 103 kg/m3 ) for solid rock (ρr) and 1000 kg/m3 (1.000 x 103 kg/m3 ) for water (ρw), determine the following values: 1) • Dry soil: bulk density (kg/m3 ) and porosity (%) 2) • Saturated soil: mass (kg). 3) • Field capacity soil: degree of saturation (%) and volume wetness (volumetric water content) (%).
A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
3.) The volume of a rock is found to be 0.00020 m3. If the rock's specific gravity is 2.50, what is its weight? (Note: g = 9.81 m/s2) 4.) A quart of SAE 30 oil at 68 °F weighs about 1.85 lb. Calculate the oil's specific weight, mass density, and specific gravity.
Figure below shows a flatboat hull that, when fully loaded, weighs 150 kN. Parts (b)-(d)show the top, front, and side views of the boat, respectively. Note the location of the center ofgravity, cg. Determine whether the boat is stable in fresh water. The depth of submergence ofdraft of the boat is 1.06 m.(Answer: Ymc = 0.983 m, Ymc is greater than Ycg, therefore the flatboat is stable in freshwater)
A 100 kg block is resting on a smooth inclined surface. Determine the value of T to maintain equilibrium.
Specific Gravity =(W_(S))/((W_(SSD)-W_("submerged "))) Explain how (W_(SSD)-W_("submerged ")) represents the "weight of an equal volume of water".
A cylindrical tank 2.20 meters in diameter and 15 meters high is filled with liquid Z. Apressure gage at elev. 10m at the side of the tank reads 105 kPa.Another gage at elev. 6m reads 140 kPa. Compute the specific weight of the liquid, density and specific gravity.
Find the weight of a 1.2 m3 dry rock mass, having a porosity of 1%. The specific gravity of the rock mineral is 2.69.