24. A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 90 MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 P/2 8 mm 8 mm (a) 56.70 kN (c) 36.19 KN I 12 mm (b) 43.29 KN (d) 21.65 kN P/2

24. A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 90 MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 P/2 8 mm 8 mm (a) 56.70 kN (c) 36.19 KN I 12 mm (b) 43.29 KN (d) 21.65 kN P/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the following data:Cross section: 50mm x 75mmP = 200 kNθ = 15 ° with the x-axis Find the shear stress (in MPa) on plane A-A.
The plate shown is fastened to the fixed member by seven 12-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 75 MPa. If P = 8000 N, what is the minimum shearing stress developed in the rivet.
Six 20mm diameter rivets fasten the plate, as shown, to the fixed member. Determine the average shearing stress caused in each rivet by the P (in kilo-newton) loads. P=74 Show detailed solution
Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine thefollowing: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle baris 60 MPa. Thickness of angle bar B is 6 mm.b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is25 MPa. Thickness of angle bar is 5 mm.
the largest axial P force that the given riveted joint can safely carry. calculate. Rivet diameter D (mm)=22 and plate width B(mm)=320 . Shear stress of the rivet 1400 kg/cm2 , crush safety stress of rivet 2800 kg/cm2 and the plate tensile safety tension 1400 kg/cm2 will be taken. t1=20mm t2=37mm
The lap joint shown is fastened by 6 − 20mm diameterrivets. Assuming that P = 200KN, determine (a) theshearing stress in each rivet, (b) the bearing stress ineach plate 25mm thick and 100mm wide. Assume that the axial load P is distributed equally among the 6rivets, and the diameter of hole is 22mm.
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 263 mmBeam height = 466 mmWLL = 12.52 kN/mWDL = 18.03 kN/mSpan of the beam = 11 mPrestressing force = 323 kNeccentricity = 105 mm
. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
A two pinned end bars AB (Copper), ? = 850 ??2, ? = 120 ??? and BC (Aluminum), ? = 1000??2, ? = 70 ??? is subjected to a horizontal force of 100 ?? applied at pin B as shown in the figure, determine the horizontal displacement of pin B.
The hollow steel shaft (G= 83 GPa) must transmit a torque (torsional moment) of 32.5 Kn-m. The outside diameter D of the shaft is 300 mm Considering both limitations (in allowable torsional shear stress of 80 MPa and in maximum total angle twist of 0.1 degree per meter), determine the minimum safe thickness of the hollow shaft and find the value of polar moment of inertia considering a limitation that the total angle of twist shall not exceed 0.1 degree per meter
an 8 m long steel is pinned at the top and fixed at the bottom. the column is provided with lateral support 3m from the top in the weak direction. the properties of the column section are as follows: ix = 178.1x10^6 mm^4 ly = 18.8x10^6 mm^4 a = 8129 mm^2 fy = 400 mpa a. what is the critical effective slenderness ratio? %3d %3d b. what is the buckling stress of the column? c. calculate the critical load pc in kn