25 ft

Q: In the figure, m1 = 10kg and m2= 4.0 kg. the coefficient of static friction between m1  and the hori...

A: GIVEN: *m1=10 kg*m2=4 kg *μs=0.5*μk=0.3 TO FIND: *Acceleration of the system. * Tension of the rope....

Q: Methods and loads chapter

A: The free body diagram of the truss is as follows: Calculate the moment about point A is as follows:...

Q: First pulley ley

A: The tensions in the rope on the sides of pulley will be different due to rotational inertia. Three F...

Q: Blaise Pascal duplicated Torricelli's barometer using a red Bordeaux wine, of density 984 kg/m3, as ...

A:

Q: A. What is the angular acceleration (rad/s2) of the disk (positive CCW)?   B. What is the angular ac...

A:

Q: Q5) The motor mounted on the bracket is acted on by its 300 N weight, and its shaft resists the 200 ...

A: Write the force along the x-direction. Write the force along the y-direction. Write the force alon...

Q: The planet Saturn has a mass of 5.67(10^26) kg and a visible diameter (top of cloud layer) of 12.00(...

A:

Q: Four signs are mounted on a frame spanning a highway, and the magnitudes of the horizontal wind forc...

A: required the magnitude and the point of application of the resultant of the four wind forces when a=...

Q: *7-40. The beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm? and 8 m...

A: According to the given free body diagram  we have ∑Fy=0RAB+RCD=6 kN........1 Now taking moment at po...

Q: 6.136 The tongs shown are used to apply a total upward force of 45 kN on a pipe cap. Determine the f...

A: Given data as per the question The upward force applied = 45 KN considering FBD of the system symm...

Q: 6.140 The tool shown is used to crimp terminals onto electric wires. Knowing that a worker applies f...

A: Draw a free body diagram for the part ABD in the given diagram. Here, By is the reaction force at B...

Q: If the gears are subjected to the torques shown, determine the maximum shear stress in the segments ...

A: Given Data: The diameter of the shaft is d= 40 mm. The torque at point A is TA = -300 N·m. The torq...

Q: A torsion bar has to be manufactured with an annealed AISI 501 steel bar, so that it resists a torqu...

A:

Q: A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. T...

A:

Q: Problem # 1 An isolated cylinder-piston system is connected to a supply line through a valve. The su...

A: Given, The inital cylinder parameters are, P1 = 150 kPa V1 = 0.1 m3 T1 = 30°C = 30+273 = 303°K The s...

Q: Question 3 a) A driver and a driven gear meshes with each other with the parameters shown in Table 1...

A: 3) a)  Given data (i) Gear ratio can be calculated as below G = NdrivenNdriver     = 2015     = 1.3...

Q: A jet of water whose diameter is 5cm strikes a fixed cup with a velocity of 9.45m/s and is deflected...

A:

Q: The beam has a rectangular cross section as shown. Determine the largest intensity w of the uniform ...

A: Given data:  Bending stress in the beam, σb,max=10 MPa Determine the largest uniform intensity, w

Q: answer if a and b true or false.

A:

Q: The composite aluminum 2014-T6 bar is made from two segments having diameters of 7.5 mm and 15 mm. D...

A: Given: D1= 7.5 mm D2=15 mm m= 10 kg h=100 mm To determine: maximum axial stress developed in the bar

Q: A cylindrical rod of Ni 200 alloy has the followingproperties: E = 204 GPa, v = 0.31. It is loaded e...

A: Given data: The modulus of elasticity, E = 204 GPa. The Poisson’s ratio, ν = 0.31. The load is, P =...

Q: What is a bone stress fracture, and how does it relate to the content of this chapter?

A: Given Bone stress To find Definition Importance

Q: Please help with the following problem

A: Draw the free body diagram of the given problem: W=mgW=2000 kg9.81 m/s2W==19620 N Consider the free...

Q: For the frame and loading shown, determine the reactions at C and D.

A: Given Applied load = 150 ft To find Reaction at C and D

Q: 15-13. The 2.5-Mg van is traveling with a speed of 100 km/h when the brakes are applied and all four...

A: Given Data: The mass of the van is M = 2.5 Mg. The initial speed of the car is u = 100 km/hr. The f...

Q: 7-75. The square deforms into the position shown by the dashed lines Determine the shear strain at e...

A:

Q: Consider the same Lockheed F-104 supersonic fighter shown, with the same flight conditions of Mach 2...

A:

Q: Help me.I will give upvote.

A:

Q: Make all possible reactions between (perfect) dislocations in (11-1) and (1-1-1) in an FCC crystal. ...

A: To Make all possible reactions between (perfect) dislocations in (11-1) and (1-1-1) in an FCC crysta...

Q: Refrigerant-134a enters the coils of the evaporator of a refrigeration system as a saturated liquid–...

A: At 140 Kpa ( Refrigerant-134a table) T=-18.77°C = 254.23K Heat rejected, Q=180 KJ TO=-10°C=263 K

Q: s

A: Represent the given data with suitable variables: T1=290 KT3=1500 Kτ=14P1=P5=90 kPa

Q: A plate clutch consists of one pair of contacting surfaces. The inner and outer diameters of the fri...

A:

Q: A thin, homogeneous wire is bent to form the perimeter of the figure indicated. Locate the center of...

A:   Let us divide the given figures into two namely 1 and 2.The coordinates of centriod of figure 1 fr...

Q: The ball rolls without slipping on the fixed surface as shown. What is the direction of the velocity...

A: The ball is rolling without slipping so the instantaneous centre of the ball is at the point of cont...

Q: Two forces P and Q are applied as shown to an aircraft connection. Knowing that the connection is in...

A: Resolving the forces in x and y direction, For equilibrium, the total horizontal and vertical compo...

Q: A reservoir has a mass of 2000kg and a volume of 1 cubic meter. Find its weight density, mass densit...

A:

Q: Methods and Loads chapter

A: Draw the free body diagram for the above problem.  

Q: do fast

A: Data given- A force of 600 N at given angles by x,y and z axis            Answer-  

Q: 6. The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficie...

A:

Q: When does the magnitude of stress increase?

A: When a body undergoes deformation under normal or shear forces/loads, then it undergoes deformation(...

Q: A submerged horizontal flat plate is suspended in water by a string attached at the centroid of its ...

A: As per the question, the axis passes through the centroid of the horizontal flat plate and the plate...

Q: Engineering stress and strain are calculated using the actual cross-sectional area and length of the...

A: When a body is subjected to normal force then the stress developed in the body will be equal to the ...

Q: The firing lines on an oscilloscope pattern are all abnormally low. Technician A says that the probl...

A: Solution:

Q: The resultant of the forces P1, P2, and the couple C is the force R= 35.6k N acting at a point A (R ...

A: Given: The resultant force is R = 35.6k N.

Q: A 2.5-kg homogeneous disk of radius 80 mm rotates at the constant rate ω1 = 50 rad/s with respect to...

A: Given, ω1 = 50 rad/s ω2 = 12 rad/s α2 = 8 rad/s2 DC = CE = a = 150 mm = 0.15m CB = b = 120 mm = 0.12...

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.