250 mm 300 mm B с -30-mm diameter -50-mm diameter PROBLEM 2.5₁ A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, = 200 GPa, as = 11.7x10-6/°C) and portion BC is made of brass (E = 105 GPa, a=20.9x106/°C). Knowing that the rod is initially unstressed, determine the compressive force induced in ABC when there is a temperature rise of 50°C.

250 mm 300 mm B с -30-mm diameter -50-mm diameter PROBLEM 2.5₁ A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E, = 200 GPa, as = 11.7x10-6/°C) and portion BC is made of brass (E = 105 GPa, a=20.9x106/°C). Knowing that the rod is initially unstressed, determine the compressive force induced in ABC when there is a temperature rise of 50°C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flat brass bar has length L, constant thicknesst, and a rectangular cross section whose widthvaries linearly between b2 at the fixed support to b1at the free end (see figure). Assume that the taper ofthe bar is small. The bar has modulus of elasticity E.Calculate the displacements δB and δC if P = 200 kN,L = 2 m, t = 20 mm, b1 = 100 mm, b2 =115 mm,and E = 96 GPa.
c. Calculate "P" in KN considering failure on bearing on projected area. Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
14. A steel column carries an axial load of 800 kN and a moment of 69 kN-m at the top and moment at the bottom which is only70% of the moment at the top. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties: A = 12886 mm2 rx is 109 mm ry = 94 mm Sx = 1200 x 103 mm3 K = 1.0 L= 3.6 m E = 200,000 Mpa Fy = 248 Mpa Use NSCP specification for compressive stress and Fb =148 Mpa. Determine the Bending Stress if Bending alone existed. Round your answer to 2 decimal places.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
plzzzz help me nowww What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
The following shaft, having a diameter of 20 mm, is made of steel (Sut = 520 MPa, Se = 260 MPa) and is subjected to a fully reversed transverse force F = 60 N and a fully reversed torque T = 30 N.m. The shaft is fixed at its left end. Find the factor of safety at A for infinite lifetime using the modified Goodman diagram. -100 mm 20-mm D. Select one: O a. Nf = 7.82 O b. Nf = 6.72 O c. Nf = 5.89 %3D O d. Nf = 9.37
A worker applies the forces P = "-50i" + 40j N and Q = 50i N to the hand- grips of the electric drill. These forces are equivalent to the force R = 40j N acting at the tip of the drill and the couple C = "-1800j" N mm Determine the dimensions a and b.
A line is recorded as 472.90m long. It is measured with a 0.65kg tape which is 30.005m long at 20C under a 50N pull supported at both ends. During measurement, the temperature is 5C and the tape is measured on 3% grade. E=200GPa. cross sectional area of tape is 3mm and the coefficient of linear expansion is 0.0000116m/"C. A) Compute for sag correction ... Please also indicate how to get the (Pm pull during measurement)
d. Calculate "P" in KN considering failure on shear on rivets Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1179.9 Nm, U = 4330 Nm, x = 3.03 m, y = 2.25 m, z = 1.34 m, d = 94 mm, and e = 76 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places.
NOTE: Wp= 'ac' lb = 33 lb. In other words the weight of the pipe is 33 lb. a) If the bolt exerts a force of 50 lb on the pipe in the direction shown, compute the force (lb) that the smooth contacts (i) at A exerts on the pipe. (ii) at B exerts on the pipe. b) Determine the maximum weight of the pipe (lb) that the vise can hold if the magnitude of the forces at A and B are equal.
Must include explanation , Don't Just copy ,I will rate accordingly. Q: A square ABCD has sides equal of 200 mm (Figure Q2 (a)). Forces of 150 N each act along AB and CD and 250 N acting along CB and AD. Evaluate the moment of the couple, which will keep the system in equilibrium.