ERсCalculate the circuit's active, reactive and apparent powers and it's power factor. Give the answers to one decimal place. R = 40N, L = H, C =E = 640V0° and angular frequency omega = 377rad/s. Give the angle in degrees.Power factor:kV ArThe absolute value of the apparent power and it's phase-shift angle:Active power:kW(NOTE! only one try is allowed for active power and after that the correct active power is given as a hint for the calculation of reactive and apparentpower)Reactive power:25000kVAF₁

Answered: Image /qna-images/answer/1828f1f7-6223-406a-96ae-10e946c9cca8.jpg

25000 ate the circuit's active, reactive and apparent powers and it's power factor. Give the answers to one decimal place. R = 400, L=H.C= F. 40V0° and angular frequency omega = 377rad/s. Give the angle in degrees. R power: kW ! only one try is allowed for active power and after that the correct active power is given as a hint for the calculation of reactive and apparent ) ve power: kV Ar solute value of the apparent power and it's phase-shift angle: factor: kVA

25000 ate the circuit's active, reactive and apparent powers and it's power factor. Give the answers to one decimal place. R = 400, L=H.C= F. 40V0° and angular frequency omega = 377rad/s. Give the angle in degrees. R power: kW ! only one try is allowed for active power and after that the correct active power is given as a hint for the calculation of reactive and apparent ) ve power: kV Ar solute value of the apparent power and it's phase-shift angle: factor: kVA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The variable resistor Ro in the circuit shown is adjusted until maximum average power is delivered to Ro.1. a) What is the value of Ro in ohms?2. b) Calculate the average power delivered to Ro.3. c) If Ro is replaced with a variable impedance Zo, what is themaximum average power that can be delivered to Zo?4. d) In (c), what percentage of the circuit’s developed power isdelivered to the load Zo?
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
The following is given for a series R-L-C circuit: resistor (R) = 8 Ohms, an inductor (L) = 32 mH and a capacitor (C) = 800uF. The circuit is supplied by a voltage source of e = 120 sin (125t) Volts. What is the angular frequency of the ac source? What is the circuit impedance? What is the power factor? What is the real power of the circuit?
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
For the series Ac circuit if e(t) = 6 sin(314t + 60°) : D 2) 3) N 5) Determine Zr Draw the impedance diagram. Calculate I, Vg, Ve and Ve. Draw the phasor diagram of the voltages E, Vg, Vi, Vcand I Calculate the total power factor, and indicate whether it is leading or lagging, and calculate the average power delivered to the circuit. 3Q 5Q AW if c@ e
In the circuit below, find the value of the load impedance ZL, which must be connected to the output of the circuit for MAXIMUM POWER TRANSFER. If this load impedance you found is connected, the amplitude of the current that will pass through the circuit, the phase angle and the angular frequency of the circuit are given in which option correctly. AB=61 AB=16 Answers I need: current= ?? angular frequency = ?? phase angle = ??
Calculate the average power abosorbed by each passive component in the circuit diagram and determine the total average power supplied by the current source. (Given answer : P3Ω=56.60W, P4Ω=33.96W, PL=0, PCS=90.50W)
a. Find the total impedance ZT in polar form b. Draw the impedance diagram c. Find the current I and voltages VR , VL , and Vc in phasor form d. Draw the phasor diagram of the voltages E, VR, VL and VC, and the current I. e. Verify Kirchhoff’s voltage law around the closed loop. f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging.
A. Find the total impedence Zt in polar form. B. Draw the impedence diagram. C. Find the current and voltages Vr,VL and VC in phasor form. D. Draw the phasor diagram of voltage E,VR,VL and VC and the current I. E. Verify kirchoff's voltage law arround the closed loop. F. Find the average power delivered to the circuit. G. Find the power factor of the circuit, and indicate whether it is leading or lagging. H. What happened if Xc=2ohm? Please explain.
In the given circuit, the amplitude of the input voltage is 160 Volts RMS and its phase is 35 degrees.The powers given/received by the elements are given below.Accordingly, which of the following is the amplitude (absolute value, modulus) of the equivalent impedance of three parallel loads. Load 1 = 11 kW and 5 kVAR Load 2 = forward 7 kVA with 0.7 power factor Load 3 = 11 kW back with a power factor of 1.0
Kindly help me with my assignment: 1. A three phase motor can be regarded as Balanced "Wye " load. A three motor draws 5.6 KW when the voltage is 225 V and the line current is 18.5 Amperes. Determine the apparent power and the power factor. 2. A single phase circuit with a given load 5 ohm resistance and capacitive reactance of 2 ohms as well. The voltage is being supplied 120Volts with a reference angle of 30 degrees at 60 Hertz frequency. Solve for P, Q, S. and power factor.
The amplitude of the voltage Vs (t) is 2 1/2 150 volts, the phase angle isQs = 0 degrees, its period is T = 200Pi microseconds.Since R = 300 ohms and C = 1 pico farad:a) Find the values of R0 and L0 that allow the load to draw the maximum average power from the circuit.b) Calculate the complex power on the load.