2/A Cubic tank 10*10*10m is initially filled with water. At the Bottom 8f the lanR there is a hole of radius 0.1m through which the water drains under the influence of gravity. Find the depth of the water in the tank at any time t, and determine how long it will take the tank to drain completely. 10x10-10

2/A Cubic tank 101010m is initially filled with water. At the Bottom 8f the lanR there is a hole of radius 0.1m through which the water drains under the influence of gravity. Find the depth of the water in the tank at any time t, and determine how long it will take the tank to drain completely. 10x10-10

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please put some illustrationAn open cylindrical vessel 1.2m in diameter and 2.1m high is 2/3 full of water. Compute the amount of water in liters that will be spilled out if the vessel is rotated about its vertical axis at a constant speed of 90rpm.
Please indicate the given and illustration A cylindrical vessel 3m high and 1.5m in diameter is filled with water to a depth of 2.5m. In its side is a 50mm circular orifice C = 0.60 placed 300mm above the bottom of the vessel. If the vessel be rotated about its own axis at 60 rpm and the water allowed to escape through the orifice for a period of 3 minutes, determine the following: A) Compute the difference in elevation, in meters, of the water surface at the center and at the periphery of the tank at end of the 3 minutes B) How deep will the water stand in the vessel if brought to rest?
Find the volume of water in the horizontal cylindrical tank if it is 7/8 full. Radius of tank is 600mm and the length of the tank is 5m. If tank is placed in a vertical position, what is the depth of water inside the tank? A. 5.13m B. 4.38m C. 4.71m D. 3.37m
A 0.09m^2 standard circular orifice is illustrated in a 2m^2 square vessel that is 3m high. Make the time to use the aperture to empty the vessel C equals 0.60. Answer t = 32.26 sec
A 2m^2 square vessel, 3m high shown has a 0.09 m^2 standard circular orifice. Find the time toempty the vessel through the orifice. C = 0.60.
Q6: What is the flow rate that flow through the main pipe that contain water? •D = 300 mm Ans: Q=0.5655 m/sec EL=23m D = 120 mm 100 mm Hg
A 12-inch diameter pipe 9200 ft long (f = 0.024) discharges freely into the air at an elevation 18 ft below the surface of the water intake (Fig. X8.28.7). What would be the percent increase in flow if a pump was added with a pump curve given by hp = 70-5Q2?
1. What is the velocity at the 50 mm pipe in m/s? 2. What is the velocity at 30 mm pipe in m/s? Thankyou ill upvote
Fluid mechanics Water flows in a 15-in. diameter full-flowing cast-iron pipe. The friction slope is 0.00640 ft/ft. Find the discharge in units of gpm (gallons per minute) and cfs (cubic feet per second). Use the equation Q = 0.279CD2.63S0.54
9.4.2 Bernoulli Equation Example 9-407 The Orifice Origin: Textbook Compute the velocity of the water through an orifice that is draining a 10-m high tank.
A 1m x 2m inclined plate is submerged as shown. The normal force acting on the upper surface of the plate due to the water (when taking atmospheric pressure into account) is most nearly (A) 68kN (B) 91kN (C) 203kN (D) 294kN Answer is 294kN. Use paper sheet to solve with diagrams
An open circular cylinder of 20 cm diameter and 100 cm long contain water up to a height of 80 cm. It is rotated about its vertical axis. Find the speed of rotation in rpm when no water spills. a.198.65 b.267.51 c.345.89 d.422.98