2)The forces and couples shown are applied to two screws as a piece of sheet metal is fastened to a block of wood. Reduce the forces and the couples to an equivalent wrench and determine (a) the resultant force R, (b) the pitch of the wrench, (c) the point where the axis of the wrench intersects the xz-plane.

2)The forces and couples shown are applied to two screws as a piece of sheet metal is fastened to a block of wood. Reduce the forces and the couples to an equivalent wrench and determine (a) the resultant force R, (b) the pitch of the wrench, (c) the point where the axis of the wrench intersects the xz-plane.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter3: Resultants Of Force Systems

Section: Chapter Questions

Problem 3.17P: The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1...

See similar textbooks

Similar questions

The forces and couples shown are applied to two screws as a piece of sheet metal is fastened to a block of wood. Reduce the forces and the couples to an equivalent wrench and determine (a) the resultant force R, (b) the pitch of the wrench, (c) the point where the axis of the wrench intersects the xz plane.
The frame shown is subjected to a horizontal force F = {300j} N. Determine the magnitudes of the components of this force parallel and perpendicular to member AB.
Four pegs of the same diameter are attached to a board as shown. Two strings are passed around the pegs and pulled with the forces indicated. Determine the diameter of the pegs knowing that the resultant couple applied to the board is 1132.5 lb·in. counterclockwise.
A stake is being pulled out of the ground by means of two ropes as shown. Knowing that a= 30°, determine by trigonometry (a) the magnitude of the force P so that the resultant force exerted on the stake is vertical, (b) the corresponding magnitude of the resultant.
The man exerts a force P of magnitude 150N on the handle of the wheelbarrow. Knowing that the resultant of the force P, Q, and W (wt of the wheelbarrow) is zero, determine W.
A beam supports three loads of given magnitude and a fourth load whose magnitude is a function of position. If b = 1.5 m and the loads are to be replaced with a single equivalent force, determine (a) the value of a so that the distance from support A to the line of action of the equivalent force is maximum, (b) the magnitude of the equivalent force and its point of application on the beam.
A force and couple act as shown on a square plate of side a=25 in. Knowing that P=60 lb, Q=40 lb, and α=50°, replace thegiven force and couple by a single force applied at a point located(a) on line AB, (b) on line AC. In each case determine the distance from A to the point of application of the force.
Slider P can move along rod OA. An elastic cord PC is attached to the slider and to the vertical member BC. Knowing that the distance from O to P is 6 in. and that the tension in the cord is 3 lb, determine (a) the angle between the elastic cord and the rod OA, (b) the projection on OA of the force exerted by cord PC at point P.
A disabled automobile is pulled by means of two ropes as shown. The tension in rope AB is 2.2 kN and the angle α is 25°. Knowing that the resultant of the two forces applied at A is directed along the axis of the automobile, determine by trigonometry (a) the tension in rope AC, (b) the magnitude of the resultant of the two forces applied at A.
A disabled automobile is pulled by means of two ropes as shown. The tension in rope AB is 2.2 kN, and the angle a is 25°. Knowing that the resultant of the two forces applied at A is directed along the axis of the automobile, determine by trigonometry (a) the tension in rope AC,(b) the magnitude of the resultant of the two forces applied at A.
Two bolts at A and B are used to move the trunk of a fallen tree. Replace the forces exerted by the ropes with an equivalent wrench and determine (a) the resultant force , (b) the pitch of the wrench, (c) the point where the axis of the wrench intersects the yz plane.
Four forces are applied at a joint of a structure. Determine the magnitude and direction of the resultant of concurrent forces.