3) A truck and trailer combination having the axle loads as shown in the figure rolls across the simply supported beam with a span of 12 meters. Determine the maximum shear force and bending moment and draw the shear and bending moment diagrams where the maximum moment occurs. P1=20 kN P2-30 kN P3=40 kN P3-30 KN 4m whim 2m 12m 2m

3) A truck and trailer combination having the axle loads as shown in the figure rolls across the simply supported beam with a span of 12 meters. Determine the maximum shear force and bending moment and draw the shear and bending moment diagrams where the maximum moment occurs. P1=20 kN P2-30 kN P3=40 kN P3-30 KN 4m whim 2m 12m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum ultimate positive and negative moments for the simply supported beam withan overhang under different loading patterns of live load combined with dead load. Also draw the shearand moment diagrams and calculate the location of the point of inflection. WD = 20 KN/m (including selfweight), WL = 30 KN/m.
Determine the member end moments and reactions for the continuous beam shown in the Figure (a) due to the uniformly distributed load and due to the support settlements of 10 mm at A, 50 mm at B, 20 mm at C, and 40 mm at D. Use the three-moment equation. Ans. MB =115.2 kN.m , MC = 451.2 kN.m, Ay = 138.5 kN, By = 277.9 kN, Cy = 378.7 kN, Dy = 104.9 kN
Determine the reaction forces R1 and R2 and show the shear and bending moment diagram. Data: Point load (left-most) = 90.126 N RL1 (80mm to 160mm) = 65 N RL2 (160mm to 180mm) = 130 N RL3 (180mm to 260mm) = 65 N
A beam with simple supports is subjectedto a trapezoidally distributed load (see figure).The intensity of the load varies from 1.0 kN/m atsupport A to 2.5 kN/m at support B.(a) Draw the shear-force and bending-moment diagramsfor this beam. Assume that M0 at B is zero.(b) Find the required moment M0 at B so that themaximum moment in the beam does not exceed1.0 kN.m.
M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and w1 = 1.5kips/ft is distributed along the length of the beam which is 22 ft. If the1.5kips/ft uniformly distributed load will be transformed into a singularconcentrated load, what will be the magnitude of Moment taken at pointA? What is the equivalent singular Resultant force of the loads shown?Determine the location of the resultant R from point A.
The simple beam AB, shown below, supports a concentrated load of 6 kN and a segmentof non-uniform load of intensity varies from 1 kN/m to 3 kN/m at point B.1- Draw the shear force and the bending moment diagrams for the beam.2- Determine the shear force (V) and bending moment (M) at a cross section located 3.0 m from the support A
the simple beam shown below is subjected to a series of wheel loads and a uniform live load magnitude of 20 kN/m. Determine the maximum moment (in kN.m) developed at point C of the beam due to the loads.
Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 3.) Determine the shear equation for segments B-C 4.) Determine the moment equation of segment C-D 5.) Determine the maximum negative moment 6.) Determine the maximum positive shear 7.) Determine the maximum positive moment 8.) Determine the moment equation for segment A-B 9.) Determine the moment equation at segment F-G 10.) Determine the vertical reactin at F
Give me the solutions of this. Identity the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m
M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and w1 = 1.5 kips/ft is distributed along the length of the beam which is 22 ft. If the 1.5kips/ft uniformly distributed load will be transformed into a singular concentrated load, what will be the magnitude of Moment taken at point A? What is the equivalent singular Resultant force of the loads shown? Determine the location of the resultant R from point A.
Determine the maximum positive shear and moment at C due to wheel loads of the moving truck shown below.
1. Calculate the moment at right end of span BC (MCB) in kN.m.0 2. Calculate the shear force at left end of span AB in kN.m.0 3. Calculate the shear force at right end of span AB in kN.m.0 4. Calculate the shear force at left end of span BC in kN.m.0