3 Absorption loss is caused by:(a) insufficient stirring of the ingredients during manufacture(b) changes in the density of the fiber due to uneven rates of cooling(c) microscopic cracks in thể cladding which allow leakage of the vacuumin the core(d) impurities in the fiber4 Rayleigh scatter is most severe:(a) in light with a short wavelength(b) in blue light on the Earth and black light on the moon(c) in low frequency light|(d) at sunset5 Bending losses:(a) always result in breakage of the fiber(b) can be caused by microbends and macrobends(c) are used to detect the length of fiber on a drum(d) are caused by the difference in the operating temperature of the corecompared with the cladding on active fibers

As per the guidelines given, We can only provide the solution of the first question in multiple type…

3 Absorption loss is caused by: (a) insufficient stirring of the ingredients during manufacture (b) changes in the density of the fiber due to uneven rates of cooling (c) microscopic cracks in thẻ cladding which allow leakage of the vacuum in the core (d) impurities in the fiber

3 Absorption loss is caused by: (a) insufficient stirring of the ingredients during manufacture (b) changes in the density of the fiber due to uneven rates of cooling (c) microscopic cracks in thẻ cladding which allow leakage of the vacuum in the core (d) impurities in the fiber

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q1. How “composite material - aerofoil blade" delivers more efficiency than other shape & materials…

A: The explanation is as follows.

Q: At a temperature of 25°C (common temperature for components in an enclosed operating system),…

A: This problem belong to analog electronics . It is about calculation of thermal voltage at a…

Q: A uniform 2-wire d.c. distributor 500 meters long is loaded with 0.4 ampere/ meter and is fed at one…

A: i have explained in detail in below steps

Q: what is the result and discussion about the different thermal and optical properties of agricultural…

A: Thermal properties of agricultural commodity For any growth of thermal system, important properties…

Q: 1. With the use if canva.com provide an infographic material in answering the following questions.…

A: The power system consists of power generation, transmission, and distribution. The transmission…

Q: A 250 m, 2-wire d.c. distributor fed from one end is loaded uniformly at the rate of 0·8 A per…

A: Given values are = Voltage at far end is Vd = 250 Volt.

Q: Find the resistance at 20°C of an annealed copper bus bar 3 m in length and 0.5 cm by 3 cm in…

A: The resistance of a wire is proportional to the length inversely proportional to the area After…

Q: 3. What is a cell in cellular system? a) A group of cells b) A group of subscribers c) A small…

A: The solution is provided in the following section.

Q: stability

A: 1) If all the roots of the characteristics equation (poles) have negative real part, the system is…

Q: ch UML diagram shows how objects of system interact with each other to complete process. ver:

Q: Biogas can be used for cooling purposes. Select one: True False

A: Biogas It is a combination of gases generated by the decomposition of material in the absence of…

Q: . Find the resistance of a manganin wire

Q: i) Calculate V1 and V2 for the voltage across the string insulator having phase voltage of 33kV for…

A: Part (ii): Since the operating phase voltage of the transmission line is 33 kV, then the number of…

Q: For the case of the thin copper wire, suppose that the number of flaws follows a Poisson…

Q: Q3) Machines A and B make components, which are then placed on a conveyor belt. Of those made by…

Q: Splicing gives a non permanent joint between two bare fibers Select one: True False

A: In this question we need to verify the given statement is true or false..

Q: ) Name and explain any two methods for improving string efficiency. (1) A string of suspension…

A: The various method to improve string efficiency. 1. By using longer cross arms- the value of string…

Q: 3. Consider the following scenario: A civil engineering student measures the resistivity of a…

A: (a) From the given data, the cross-sectional area of the wire is constant as the radius is constant,…

Q: determine the diameter of manganin wire 68.7 meter long which has 8.86 ohm resistance if the…

Q: Discuss four classifications of biomass materials. Suggest at least four such materials which are…

A: The four classification of biomass materials are Woody biomass (includes trees, shrubs and bushes)…

Q: How can you measure the temperature of an object using the Calendar-Griffith's bridge, Explain in…

A: Calendar-Griffith's bridge- It is one type of potentiometer used to calculate the voltage difference…

Q: #1

A: part(a) it is possible that two distinctive measured filaments can be joined. Transmitting from a…

Q: The property of insulating material which makes the breakdown voltage high in a cable i . ******** O…

A: Dielectric strength is maximum field that can a insulating material can withstand without break…

Q: 24. What is the size in square millimeter (mm^2) is the cable of 300 MCM? (Solution) 150 mm^2 350…

Q: 3 (ii) Find the diffusion co-efficients of electrons and holes of a single silicon crystal at 27°C,…

A: Given: A single silicon crystal having T=27°C=300 Kμn=0.17 m2/volt-secμp=0.025…

Q: the 19 strands of a cooper cable has a diameter of 59 mils. Calculate the resistance of a foot of…

Q: 1. Absorption loss is caused by: (a) Insufficient stirring of the ingredients during manufacture.…

A: Absorption loss in optic fiber is caused by mainly 3 reasons. 1. Intrinsic Material Absorption 2.…

Q: Identify the following elements from the given block diagram. a)Measurement Element b)Process…

A: block diagram.a)Measurement Element_speed sensorb)Process Element _ throttle unit

Q: 4. Which of the following can't be included in data required for coordination study? a) X/R Ratio b)…

A: as per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: aluminum wire of unknown cross section has diameter of 0.635 cm and a resistance of 0.28ohm. If the…

A: We know direct relationship for resistance and area of a conductor .

Q: -1 Synthesis of nanomaterial from larger bulk Top-Down method Select one: O True O False

A: Generally in Top- Down method , the synthesis of nano materials from larger bulk .

Q: Electrical Engineering A semiconductor fabrication plant has an average output of 10 million devices…

A: Semiconductor: The electrical conductivity of a semiconductor material varies between that of a…

Q: (i) Find the equation of the calibration curve using Newton's divided difference of third order…

Q: Please discuss the potential risks of the electrical machines to the environment and the important…

A: Please discuss the potential risks of the electrical machines to the environment and the important…

Q: Determine the largest relative error in a calculation of the cross-sectional area of a wire from a…

A: measurement of diameter D= 0.825±0.002 cm Determine the largest relative error in a calculation of…

Q: The Permittivity of the Insulators increases when the Insulators suffers from cracks or breakages.…

A: Given Permittivity of insulator increases when it suffers from cracks or breakages.

Q: 2. Write the function of autotransformer in the Laboratory

A: An autotransformer is used for the adjustment of the line voltages to change their value or keep it…

Q: A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.12 of…

Q: Proposesome method to quantize the quality of a thermos insulation.

A: THERMAL INSULATION Thermal insulation is the technique of preventing heat from being transferred…

Q: A 2-wire d.c. distributor 300 metres long is uniformly loaded with 4A/metre. Resistance of single…

A: We have a DC 2-wire distributor which is, Length of distributor (l) = 300 meter Current (i) = 4 A /…

Q: roll two dice and observe two numbers X and Y . If Z = X − Y , find the range and PMF of Z.

Q: a) Explain FOUR (4) measurement standards available. b) Explain the difference between systematic…

Q: Discuss the relation of location of poles on stability of a system. Explain with neat graphs

Q: a) Draw the block diagram of a measurement system. b) Explain the primary element of a measurement…

Q: Determine the length ℓ of the resistance of the insulation in a length l of a coaxial cable.

Q: Determine the resistance of a bus bar made of aluminum at 50°C if the length is 15 meters long and…

A: to determine the resistance of a bus bar made of aluminum at 50°C if the length is 15 meters long…

Q: 1. Suppose a 12-gauge copper wire, which has twice the diameter of the common 18-gauge wire (1.02mm…

A: The given formula is: I=nqvdA................(i)where,I=currentn=no. of electronsq=charge of…

Concept explainers

Gear Motor

A gear motor is a combination of a gearbox and an electric motor. This combination of two systems is used for efficient usage of the motor. It makes a cost-effective solution for high torque, low-speed applications. These motors are used in our household as, garage door openers, alarm clocks. In commercial areas, hospital beds, cranes.

Question

3 Absorption loss is caused by:
(a) insufficient stirring of the ingredients during manufacture
(b) changes in the density of the fiber due to uneven rates of cooling
(c) microscopic cracks in thể cladding which allow leakage of the vacuum
in the core
(d) impurities in the fiber
4 Rayleigh scatter is most severe:
(a) in light with a short wavelength
(b) in blue light on the Earth and black light on the moon
(c) in low frequency light|
(d) at sunset
5 Bending losses:
(a) always result in breakage of the fiber
(b) can be caused by microbends and macrobends
(c) are used to detect the length of fiber on a drum
(d) are caused by the difference in the operating temperature of the core
compared with the cladding on active fibers

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Estimate the optical loss due to Fresnel reflection at a fiber core from GaAs each of refractive indices 1.48 and 3.5 respectively. b) Calculate the optical power emitted into air for the device, when the step index fiber has a numerical aperture of 0.16, coupled power of 0.31 mW.c) Determine the overall power conversion efficiency for the LED if it is operating with a drive current of 210 mA and a forward voltage of 1.5V.d) Find the optical output power at 170MHz, and calculate the optical and electrical modulation bandwidth for a minority carrier recombination life time of 9ns.
A typical glass core optical fibre has a specified transmission loss factor of 0.046 dB/km due to Rayleigh scattering. At a wavelength of 1000 nm, the glass material possesses an approximate fictive temperature value of 758K, an isothermally compressibility parameter of 8.4 × 10-11 m2/N, and a photo-elastic coefficient of 0.245
ATR works by measuring the changes that occur in an internally reflected IR beam when the beam comes into contact with a sample.. True False
Question 4. Select the statement that best describes the PM wave.a. Carrier phase angle changes represent the PM modulated signal, however, unlike FM and AM modulatedcarriers, it is not always easy to see these phase changes in the plot.b. The FM signal accurately represents the message.c. Although PM and FM techniques are classified as angular modulation techniques, they cannot be usedinterchangeably (i.e., modulated with FM and demodulated with PM, and visa versa).d. All statements are correct.
(i) At what wavelength are the rates of spontaneous emission and stimulated emission equal in a two-level system at room temperature? (ii) A GaAlAs laser diode has a 500 μm cavity length which has an effective absorption coefficient of 10 cm-1. For uncoated facets the reflectivities are 0.32 at each end. What is the optical gain at the lasing threshold? (iii) If one end of the laser is coated with a dielectric reflector so that its reflectivity is now 90%, what is the optical gain at the lasing threshold?
A standard waveguide WR187, has the following dimensions: outside walls 2.000 x 1.000 in., wall thickness 0.064 in. Determine the highest frequency that can be transmitted if only the TE10 mode is permitted. What modes can exist in it if it is excited by a wave of frequency 6.00 GHz?
Find the numerical aperture ‘θ’ if the MN = 6 cm, PR = 8 cm and the distance from the tip of the connector to the surface is 4 cm
A satellite at an altitude of 37654 km transmits a signal of 17 GHz to a ground station directly below it. The following data is given. • Total atmospheric losses = 40dB • Transmit antenna gain = 55dBi • Receiver antenna gain = 60dBi • Signal to noise ratio of received signal = 6dB • Receiver signal noise power = 25pW • Receiver sensitivity = -90dBW I. Calculate the power transmitted. II. Find the Fade Margin for the link and comment on your result.
A GaAs DH injection laser (refractive index: 3.6) has an optical cavity of length 50 μm and width 20 μm. At normal operating temperature (300 K) the loss coefficient is 10 cm-1, the mirror reflectivity at each end of the optical cavity is 0.3 and the gain factor for the device is 3.76x10-2 cm/A. The device emits at a wavelength of 870 nm
1. Discuss in detail the construction of a Directional Coupler. 2. Discuss in detail whether the incident energy can be sampled or not with pick up probe at port ‘4’.
P2/ an FM transmitter operates with a total power of 10 w, a frequency deviation of 5 KHz and a modulation index of 2. If the receiver has a sufficient bandwidth for Include the carrier and the first two pairs of side bands, what is the percentage of Total power of the signal you receive?
Question.1 (a): Find the numerical aperture 'e if the MN = 7 cm, 5 cm and the distance from the tip of the connector to the PR surface is 4 cm. Question.1(b): If the attenuation to cross talk ratio 28 dB and the near end cross talk is 36 dB. Find the attenuation of the signal in dB.