In the circuit given below, C1=3.0 µF, C2=2 µF, C3= 7 µF, C4=5 µF, C5 = 9µF, C6=8 µF, C7= 3 µF and C3=6 µF . If the potential difference betweenpoints Vac = 100.0Va) Find equivalent capacitor and total charge?b) What is charge and electrical potential different on each capacitor ifC1, C2, and C5.2 uFHE3 µF7 uF9 µF3 uF100 voltsI I8 µF4 uF

This question is from basic network analysis. Under which we are going to find out the net…

Answered: 3 µF 2 uF 7 uF 9 µF 3 uF 100 volts 8 µF…

Engineering

Electrical Engineering

3 µF 2 uF 7 uF 9 µF 3 uF 100 volts 8 µF 4 µF

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
Consider the circuit below. a) Calculate the equivalent capacitance Ceq (show all steps) b) What is the potential difference across C4?
>Rank these 3 materials by increasing relative permittivity : Air, Glass, Hard Rubber. ____, ____, ____. >If capacitor has a code of 453D,the nominal value is ____. >The same capacitor has a tolerance of ____. >The time between when a capacitor is fully discharged to when it is fully charged is called the ____time. >Define pole ____and throw ____.
Determine the total capacitance, total charge, individual voltage drop and charges across across each capacitor. Use two decimal places for your answer. Please put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! C1= 27 F C2= 53 F C3= 21 F C4= 50 F C5= 17 F C6= 22 F C7= 45 F C8= 16 F C9= 25 F C10= 16 F V= 110 V Note: This topic is under capacitors.
A. Find the equivalent capacitance of the combination shown in the figure. (C2 = 2µF, C3 = 3µF) B. Determine the charge on each capacitor, if there is a potential difference of 900V C. Determine the voltages across each capacitor
At a potential of 7000 V, a simple parallel-plate capacitor will be built to store charge. The capacitor has a separation distance of 0.21 mm between plates and a plate area of 0.030m2.The dielectric constant of a material with a dielectric constant of 6.5 is positioned.in the space between the plates Compute the capacitance of the capacitor and compute the magnitude of the charge stored on each plate.Then,If the capacitance in above has to be increased, choose one acceptable dielectric material from Table 2 below to use between the plates.Justify your mathematical decision.
The circuit in the figure below has been connected for a long time. Let R1 = 7.80 Ω and R2 = 4.20 Ω.(a) What is the potential difference across the capacitor? which is 6.03 (b) If the battery is disconnected from the circuit, over what time interval does the capacitor discharge to one-half its initial voltage? in eed b
A 3.0 MΩ resistor and a 1.0 μF capacitor are connected in series with an ideal battery that has an emf E = 5.0 V. After 1.0 s after the initial connection is made, find the rate at which(a) the charge on the capacitor is increasing (inC/s),(b) energy is being stored in the capacitor (inJ/s),(c) thermal energy is appearing in the resistor (inJ/s), and (d) energy is being delivered by the battery (inJ/s).
A paper dielectric plate capacitor is to be experimentally tested. The metal plates and the paper material between said plates are all 20 cm in radius and subjected to 10V dc in the test. How much is the capacitance does this capacitor have in picofarads (pF), if the paper material between plates used is 2 cm thick? Input answer in 4 decimal places and in pF. Note: Relative permittivity of the paper ( εr ) : 0.4225
Solve for the (and refer to the image): - individual voltages - individual charges wherein Equivalent capacitance of the capacitor is 0.76 F Charge stored in the circuit is 45.50 C. And V= 60V
Suppose that we have a 1000-pF parallel-plate capacitor with air dielectric charged to 1000 V. The capacitor terminals are open circuited. Find the stored energy. If the plates are moved farther apart so that d is doubled, determine the new voltage on the capacitor and the new stored energy. Where did the extra energy come from?
You are given 10 resistors that are each 30 Ω. Construct a circuit with a resistance of exactly85 Ω. don't use all 15 resistors.a.) Explain process in designing the circuit.b.) Draw a diagram of the circuit,c.) Show that the total resistance for the circuit is 85Ω.d.) Suppose capacitors was given instead. Draw a circuit using 15 or fewer30 μ F capacitors, so that the circuit has a total capacitance of 85μF. Briefly explain the process.e.)Show that the total capacitance is 85μF.