3 Suppose that SS-1000H, DS-2000H, BP-1000, BX 0300H, and DI=04F0H Determine the memory address accessed by each of the following instructions, assuming real mode operation: MOV AL, [1FEFH] a) b) MOV AL, SS:[DI-8F] c) MOV BP, AL Find the contents of indicated register or memory after execution of the following 5. program. Mov ax,1750 Mov ds,ax Mov si, 0100 Mov di,200 Mov cx, 0009 Inc cx Inc si Mov al,[si+100H 1750: 0100 10 20 1750:0200 24 00 АХ- СХ- DS= SI= DI= imen

3 Suppose that SS-1000H, DS-2000H, BP-1000, BX 0300H, and DI=04F0H Determine the memory address accessed by each of the following instructions, assuming real mode operation: MOV AL, [1FEFH] a) b) MOV AL, SS:[DI-8F] c) MOV BP, AL Find the contents of indicated register or memory after execution of the following 5. program. Mov ax,1750 Mov ds,ax Mov si, 0100 Mov di,200 Mov cx, 0009 Inc cx Inc si Mov al,[si+100H 1750: 0100 10 20 1750:0200 24 00 АХ- СХ- DS= SI= DI= imen

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

using STDM 102 ARM®-based 32-bit MCUs, write an assembly routine to turn on one of the user LED’s. You have to configure the I/O lines first. This should be done in a subroutine. Now that you can control the LED, write a routine to blink the LED. HINT: toggling an LED in code happens very quickly!! Use a delay routine to leave an LED on long enough to see it light up. At the end of this phase, have your code blinking the LED off and on in a loop 10 times. Then Then write a routine such that when the user presses the switch down, the LED will come on. When the user depresses the switch the light will turn off. This is called polling the state of the switch.
Identify the contents of the registers, the memory location (C055H), and the flags as the following instructions are executed in 8085 microprocessor. A H L S Z CY M(C055H) LXIH, C055H MVI M,8AH MVI A,76H ADD M STA C055H HLT
a.Write the addressing modes of the following instructions: (i) MOV A, @R0(ii) MOVX @DPTR, A (iii) MOVC A, @A+DPTR (iv) MOV R0, #45H b) Write instructions to perform the following operations: (i) Move the content of Accumulator to register 7(R7).(ii) Move the contents of RAM memory location 55H to Port 1(iii) Receive content from ROM Memory location 200H into Accumulator.(iv) Clear bit 7 of the Accumulator.c) Why 4-20mA Current loop is widely used Industrial Standard for sensor data transmission and control. What are its advantages over 0-12V Standard? d) Two configurations of GPIB is shown in Fig. A and Fig. B. Explain the working of GPIB in both the configurations and what are the differences between the two. this question is asked in microcontroller and microprocessor
For 4.3 V, calculate is the digital output by using a Successive-Approximation ADC method? Also calculate the error. (10-bit A/D with range 0V – 10V)
choice correct answers analogReadResolution() instruction accept bit resolution up to 16 12 32 the maximum of the programmed board - For Arduino ZERO, using 2.23 V built in reference, what is the input code if the default bit resolution was used for Vin = 1 V? 458 1836 459 1837 - For memory address (133F7) h with offset of (2031) h, what is the segment address? 15442 113C 33701 135F41 - What is the input for Arduino UNO if the input voltage is 3.25 V? Assume defaults 1008 644 645 1007
Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO read, and IOW for IO writeNote 2: Use hexadecimal where possible Q/ How many T-states are required for (STA) instruction?
20] How long does it take a 3.3uF Capacitor to fully charge through a 18k Ohm Resistor? Express your answer in Decimal with 2 digits of significance. 21] What is the minimum Sum-of-Products equation for the Function 'Y = BAC + F + BC'? 22] Implement the Function 'Y = ACB + BC + E' using a 4-Input, 2-Address Bit Multiplexer. What are the Equations for the Multiplexer Data Inputs (D3 - D0)?
Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO read, and IOW for IO writeNote 2: Use hexadecimal where possible Q /- If register A contains (66 h) and CY=1, what is the result in the accumulator after (ADC A) instruction? - If register A contains (3A h) and register B contains (44 h), what are the results in the CY and Z flags after (CMP B) instruction?
Calculate the address of the bit 58 H in the bit addressable area of the 8051? Show your calculation.
3. An audio CD is created by sampling analog audio signals at a rate of 44.1 ksamples/s for each. Each sample is then encoded into a 16-bit word. What is the data rate of the resulting PCM signal? Determine also the size of data (in Mega bit unit) for 1 minute PCM signal.
Q1) List the main internal elements of a microcontroller. And explain the function of each of them. Q2) What is the difference between the Von-Neuman Microcontroller Architecture and Harvard Microcontroller Architecture. Q3) Compare between the (EEPROM) and the Non-Volatile RAM - (NVRAM). Q4) What is the term “Complex Instruction Set Computer(CISC)” mean in the Microcontroller Architecture.
For Arduino ZERO, using 2.23 V built in reference, what is the input code if the default bit resolution was used for Vin = 1 V?