3) The transfer function of a control system is given by G(s) = 25/ (s² + 6s + 25).The first maximum value of the response occurs at t, which is given by:a) π/2b) π/8c ) π/4d) n4) If the unity feedback system is given by the open loop transfer function G(s) = ks? /[(1 + 0.3s) (1+ 0.05s)], what would be the initial slope of magnitude plot?a) a. 20 dB/decadeb) b. 40 dB/decadeс) с. 60 dB/deсaded) d. Unpredictable

PEAK TIME: The time taken by the response to reach maximum value or peak value is called peak time.…

Answered: 3) The transfer function of a control…

3) The transfer function of a control system is given by G(s) = 25/ (s² + 6s + 25). The first maximum value of the response occurs at t, which is given by: a ) π/2 b) π/8 c) π/4 d) n

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

By plotting the locus-root curve of the open-loop transfer function G(s)= K / s (s+2); a) When K=4, show the locations of the closed loop poles on the root locus. Determine the damping ratio ζ and the natural frequency (wn) values at this gain value. b) Calculate and scale the unit step response of this closed-loop system by calculating the %overshoot, tp and ts (percent overshoot, peak and settling times, respectively). c) In order for this supervised system to work at least in the performance criteria (computed (greater than ζ and wn)) in question (a), scan the region where the pairs of conjugate poles should be located on the root-locus curve.
A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
For the Unity feedback Control System the forward path transfer function is given by: G(s) = 20/s(s+2)(s^2 + 2s + 20) Find the steady state Error of the System? 2. Determine the static error coefficient kp,kv and ka . G(s) = 50/(1+0.1s)(s+10) 3. Find the dynamic error coefficient of the unity feedback system whose forward transfer function is G(s) = 20/s(s+5) Find the steady state error of the system for the input 4t2
Open loop function of a unity feedback system is given by G(s)=K(s+A) / s(s+1.4)(s+2.9)(s+3.2) For drawing root locus, if the value of Centroid is -2, then The value of A is :
Find the transfer function of the electric circuit given below by the block simplification method. In case of R = 1kΩ, C = 10µF and L = 2mH, if the system operates in closed loop with negative unit feedback, find out what the k value should be in order for the system to be stable.
For a negative unity feedback system with the given forward transfer function:1. Evaluate the system type, Kp, Kv, and Ka.2. What is the value of the position constant?3. What is the value of the velocity constant?4. What is the value of the acceleration constant?5. What is the amount of steady-state error if the system received a parabolic function signal?
From the closed loop poles shown in the S plane, positioned at -1 and -40, determine:a) The 3rd order transfer function in closed loop, considering that it has a gain equal to 40; b) The 2nd order closed loop transfer function; c) The DC gain of the 3rd order transfer function and also of the 2nd order; d) The damped natural frequency, the values of tp, ts (2% criterion) and Mp, calculated from the 2nd order transfer function.
Consider unity negative feedback applied to the system: G(s) = k/s(s^2+4s+5) (a) Give a complete sketch of the root locus (0 ≤ k ≤ ∞) for this system assuming a unity feedback configuration. Make sure you show all the significant features on your sketch. Give particular attention to the angle of departure from the complex poles. (b) Indicate on your root locus diagram the point at which the damping ratio of the dominant poles is 0.5.
Consider a closed loop system with zero order hold.consider Gp(s)=400/s2+400.determine the closed loop transfer function T(z) for the system at T=1sec
1. Since this is a first order system, provide expression for the time constant. 2. Provide a state space representation of the system. 3. Obtain the transfer function of the system using the state space model. 4. Determine the control gain Kp that results in steady-state error of 0.1
1.Find the impulse response of the equivalent system (i.e,, find h[n]) such that y[n]=x[n]∗y[n]holds where h1[n]=h[n]+0.5drag[n−1], h2[n]=0.5drag[n]−0.25drag[n−1], h3 [n]=(0.5)n u[n]with u[n]denoting unit-step function. this is a signal systems question
The bode plot of the open loop transfer function of a quadratic system is shown above. If the settling time of the closed loop system is 4 seconds, calculate the undamped natural frequency of the system, the damping ratio, the highest amplitude value of the frequency response of the closed loop system and at which input frequency it occurs. Attention!!!: Use the numbers as three decimals during the design phases. Solution: Belonging to the closed-loop transfer function Damping rate = [ ? ] Undamped natural frequency = [ ? ] rad/s The highest amplitude value of the frequency response [ ? ] and [ ? ] occurs at the rad/sec input frequency.